- 1. [TenTec] Ten-Tec 706 Microphone (score: 1)
- Author: "Reed" <w4jz@ispwest.com>
- Date: Tue, 20 Dec 2005 20:10:09 -0600
- I have a Argonaut V, version 1.08, which works great with hand microphone, but I'm having to run Mic Gain all way clock wise to start ALC light to blink with the 706 desk microphone. Hand Mic Gain se
- /archives//html/TenTec/2005-12/msg00559.html (6,689 bytes)
- 2. Re: [TenTec] Ten-Tec 706 Microphone (score: 1)
- Author: "Mike Brown" <k9mi@sbcglobal.net>
- Date: Wed, 21 Dec 2005 04:42:31 -0000
- I've had Ten Tec Radios with the 705 and they really do a good job of driving the radio. Is there an amplification switch on the bottom maybe? 73, Mike K9MI __________________________________________
- /archives//html/TenTec/2005-12/msg00561.html (7,760 bytes)
- 3. [TenTec] Ten-Tec 706 Microphone (score: 1)
- Author: "Reed" <w4jz@ispwest.com>
- Date: Tue, 20 Dec 2005 23:29:46 -0600
- Thanks Mike for the reply. No, this one does not have the amplification switch on bottom. I believe I have found the problem. When I upgraded the rig to ver 1.08, year or so ago, I did not increase t
- /archives//html/TenTec/2005-12/msg00562.html (6,962 bytes)
- 4. Re: [TenTec] Ten-Tec 706 Microphone (score: 1)
- Author: RaySoifer@cs.com
- Date: Tue, 20 Dec 2005 22:49:15 EST
- Reed, My Argo V, also v1.08, must have a little more audio gain than yours, or else I just talk louder, so the numbers are a little different, but I also notice that the 706 desk mike has lower outpu
- /archives//html/TenTec/2005-12/msg00576.html (7,549 bytes)
- 5. [TenTec] Ten-Tec 706 Microphone (score: 1)
- Author: "Reed" <w4jz@ispwest.com>
- Date: Thu, 22 Dec 2005 23:36:29 -0600
- Thanks Ray for the reply. I talked with another ham last night & found, with my voice, 11 o'clock is working fine. 12 o'clock have peaks of distortion. I set the mic gain pot, inside the rig, while t
- /archives//html/TenTec/2005-12/msg00655.html (8,206 bytes)
- 6. Re: [TenTec] Ten-Tec 706 Microphone (score: 1)
- Author: "James C. Owen, III" <k4cgy_list@yahoo.com>
- Date: Fri, 23 Dec 2005 05:34:39 -0800 (PST)
- Well every mic has a different output--that's what the mic gain pot is for. My hand mic runs about 10 o'clock. I built a mic using a d-104 case and a electrat element form a junk telephone and the ou
- /archives//html/TenTec/2005-12/msg00659.html (9,216 bytes)
- 7. Re: [TenTec] Ten-Tec 706 Microphone (score: 1)
- Author: RaySoifer@cs.com
- Date: Fri, 23 Dec 2005 12:01:19 EST
- Hi Reed, Following your suggestion, I took off the bottom plate and see that the ground connection between it and the chassis is OK (through a lockwasher lug at one of the mounting screws). However,
- /archives//html/TenTec/2005-12/msg00704.html (8,349 bytes)
- 8. Re: [TenTec] Ten-Tec 706 Microphone (score: 1)
- Author: RaySoifer@cs.com
- Date: Fri, 23 Dec 2005 12:04:16 EST
- Jim, v1.08 of the Argonaut V includes some hardware mods as well as software. It was installed at the factory when I sent mine back last January for an unrelated warranty repair (a blown keyer chip).
- /archives//html/TenTec/2005-12/msg00705.html (7,708 bytes)
- 9. Re: [TenTec] Ten-Tec 706 Microphone (score: 1)
- Author: Robert & Linda McGraw K4TAX <RMcGraw@Blomand.Net>
- Date: Sun, 25 Dec 2005 14:14:02 -0600
- Don't take the foam off. It serves as a filter to reduce the effect of popped P's and huffed H's. Plus it protects the element from moisture accumulation due to condensation from the warm moist laden
- /archives//html/TenTec/2005-12/msg00733.html (9,423 bytes)
- 10. [TenTec] Ten-Tec 706 Microphone (score: 1)
- Author: "John K Gotwals" <john@gotwals.com>
- Date: Mon, 26 Dec 2005 13:43:04 -0500
- I purchased a demo 706 mike from Ten-Tec to use with my Orion, and after a week or two of operation I had to return it because the VOX and PTT buttons had suddenly become unreliable in operation. The
- /archives//html/TenTec/2005-12/msg00747.html (9,191 bytes)
This search system is powered by
Namazu