Kerry, Dick: some problem with emailing back to you. Checked QRZ.com to double check email addr, none listed. Please copy this and confirm directly to me. I have your addresses OK. Tnx, Steve, K1PEK
Hi Ian, In general, a Kings connector is a high quality connector. To be specific, if you could give me the Kings part #, I can give you specifics about the connector (Particularly the dielectric mat
<< When I see several messages like the one below, I need to ask what is this reflector about? ...... Whining, bloodletting and blasting others does not solve the problem. Tony N2TK >> I have followe
I agree with Tom, W8JI. Also, the recommendation which I have had for years, also shared by W1CF (silent key) and W1FC who mastered Colatchco, and Jim, K4SQR of Comtek Systems (Phased Array switching
One of my best mentors, best friends, and affiliated business partners is Press Jones. One of the non-tech'l things he taught me was brevity in prose. Let me one-up him (on brevity) by agreeing and r
Steve, We have several customers who build these ENG vans, trucks, military RF and power vehhicles and broadcast control tractor trailers. One is "Wolf Coach". Their tel # is 508 791 1950. Another id
Well, I can't resist two comments: Somebody mentioned something to the effect "just about any place sells these". I guess I can take pride in saying that "DAVIS RF Co." is "not just anybody", because
Hi Lane, I agree with Joe, WD5FHG: Dacron, min. stretch, UV resistant. I have used what we sell for years on my verticals and other antenna applications. We carry numerous sizes in DOUBLE braided (vs
Hi all, I realize that my following opinion has nothing, directly, to do with the scope of TTalk. The problem that has been noted about ham designed software being copied, sold, etc. is certainly abh
Bill, you should be fine with the applications you mention and no penetrox, etc. Just be sure you wrap all this up a good 2" or so onto the cable and if at all possible to the mating connector and/or
GE Fellow TTarians, We have just released a revised catalog of our ham line of various aerial wire, coax, rotar and control cable, LMR, other hard line, low cost high grade hard line/CATV connectors,
Lyn, I don't know the construction of Gem Quads but soft copper shouldn't be an issue if the quad is built well as the stresses would not be inappropriate for the wire. This is assuming a proper supe
Lyn, I don't know the construction of Gem Quads but soft copper shouldn't be an issue if the quad is built well as the stresses would not be inappropriate for the wire. This is assuming a proper supe
This is a multi-part message in MIME format. --part0_914525396_boundary Content-ID: <0_914525396@inet_out.mail.aol.com.1> Content-type: text/plain; charset=US-ASCII --part0_914525396_boundary Content
Alex, My firm is a designer and distributor of many types of wire, cable and RF peripheral devices. We handle the PolyPhaser line. I provide FREE assessments of any lightning protection situations. I
Hi, Ref the obsolete AMP cable #, sample sent to us: we have analyzed the cable, have the spec's, cost to replace, etc and managed to misplace your email address!!!. Please contact us, tnx, Steve Dav
Hi Rush, WB0W, Inc. makes a real nice gin pole. His # is 1-800-626-0834 and Email: WB0W@IBM.net. Super OM/XYL to work with. regards, Steve Davis, K1PEK, DAVIS RF Co. -- -- DAVIS RF Co., Commercial wi
HI everybody. I have a customer who is looking for a good consumer source for stainless steel hardware (nuts, bolts, washers) in the 6-32, 8-32 and 10-32 ranges. If you have some sources I will pass
Hi Folks, Thanks for the excellent response. Hopefully this list will help others and I have sent it along to the customer who was looking. Tnx again, Steve Davis, K1PEK DAVIS RF Co. : ........ My (e
<< I am also on a steep ridge, approximately 60 feet down from the top. Lots of 60-90 foot oaks and poplars. I have a hytower and have used two different W1CF/Colatchco verticals with great success i