Hello I have vertical connected to an antenna switch. I use to disconnect the coaxial that go from radial plate to antenna switch. I disconnect it in the radial plate, this is to protect if a storm w
Hello do you know about a clamp on thrust bearing? I need to replace a broken one on top of the tower and i dont want to remove 2 big antennas I have on the mast -- 73, Jorge CX6VM/CW5W _____________
Hi Grant I use it as radial only bearing. My rotor support all the weight of the mast and antennas. Thanks for the advice, will look for this to replace my broken TB 73, Jorge -- 73, Jorge CX6VM/CW5W
Hello you dan do the same with DXE-TFS4-80 box? thanks Jorge CX6VM/CW5W -- 73, Jorge CX6VM/CW5W _______________________________________________ _______________________________________________ TowerTa
Hello do you know who sell aluminium tubing, telescoping sections, to build a large vertical antenna? If near Miami, FL will be better thanks! -- 73, Jorge CX6VM/CW5W ________________________________
hello Charlie and Grant thanks very much for the advice Yes, 80 mts verticals at DXE, for 399.95 or 899.95 are very nice antennas but expensive if you are considering more than 1 antenna :-( 73, Jorg
Hello Roger and others a lot of information. Worst part will be shipping to CX Will se what I can find locally, but nothing good 73. Jorge -- 73, Jorge CX6VM/CW5W ____________________________________
very interesting Jim I always wanted to change my arraysolution sixpack, that failed several time when switching antennas My actual setup is Elecraft K3 x 2, ArralSolution Bandmasters III x 2, Sixpac
Thanks Jim wiring is with multi cables from Bandmaster to Sixpack control unit screws I know is better to have all from same manufacturer, if something fail, thet will say the fail is in the other pr
Hi John well, in my case that I dont have any skills for wiring, and setup all, I prefer something like plug and play. I always asked Jay why the sixpack boxes donīt have a connector to plug a cable
HELLO Did you use one of this on top of the tower or another one inside tower, between rotor and top of the tower? thanks, Jorge -- 73, Jorge CX6VM/CW5W ______________________________________________
Hello Geo thanks very much and I would like to know other experiences I have my setup same as you. 1 year ago I needed to remove a rotor and was a pain, mast bend with the wind, broken my thrust bear
Hello someone have close photos to see how to routing the two cables from inside the rotor reed switch? Thereīs some photos here http://www.k7nv.com/proppitch/id42.htm but couldn't see exactly what I
Hello what is better to use on this cable, the idea is to connect it up in the tower to a Buryflex with PL259 connector on the antenna rotor loop. Some on the other side, going inside the shack with
Hello I am looking for a remote IP power control for 240 volts. If you can recommend me some of this I appreciate very much I found one for 240 volts, but it have C13 outlets (sockets?), and I have m
Hello where can I find a MALE connector that fit on this one https://www.dxengineering.com/parts/dxe-cc4-con thanks!! -- 73, Jorge CX6VM/CW5W _______________________________________________ _________
Hello I want to THANKS DX Engineering and Tim K3LR, that found this parts for me and sent them to my forwarder in Miami, FL Thats a great customer service! thanks Tim! 73, Jorge CX6VM/CW5W <https://w
Hello I have a 6x2 sixpack with 6 antennas connected for 10, 15, 20, 40, 80 and 160 mts I want to add a 30 mts antenna, maybe I can connect it to the 10 mts position? But how to to the automatic band
Hello at ArraySolutions thet have a NOTE for the installation of new potentiometer for PST61D Note: You may need to drill a 1/4" clearance hole for the new pot shaft to fit in the bottom of the rotat