Where can one download a copy of this document ? Google sends me down numerous paths and none get me to it. Also, I would like the chart showing the Wind Speed in various parts of the country used in
I heard a rumor at a Flea Saturday that YAESU has discontinued the G2800. Can anyone confirm that ? Thanks, Dick, W1KSZ _______________________________________________ _______________________________
A friend bought a 4 element Two Meter Beam at a Flea on Saturday and we are trying to ID it. It has a Gamma Match and is end mounted (can be Horizontal or Vertical). It looks a lot like the Cushcraft
I think it is a misnomer to call them ..."Laws"... . They are theories that explain a phenomenon to which the majority of the scientific community subscribe to, at this present time. They are not Hol
That's because at frequencies above 14 MHZ, it makes a nice cloud warmer. The higher the frequency, the warmer the clouds get. 73, Dick, W1KSZ _______________________________________________ ________
I too would appreciate a copy, Thanks, Dick, W1KSZ _______________________________________________ _______________________________________________ TowerTalk mailing list TowerTalk@contesting.com http
Before I take the Rotor apart I would like to have the Ball Bearings on hand. Can anyone tell me the diameter and material (SS or Chrome Plated) of them ? Tnx, Dick, W1KSZ ___________________________
So far, I have received two responses on the size. One said 1/4", the other said 3/8". Sort of renews my faith .... Guess I'll just open the thing up and measure them. 73, Dick, W1KSZ _______________
I have the Butternut HF-2V. I added two more taps to the 80 meter coil and use 3 relays to select the tap I want (3500, 3600 and 3800). I can select the relay from the shack and it works quite well.
I picked up a 350' length of NIB LDF4-50A. Where can I find a list of connectors I can use on it ? I have a few in my stash (44ASW, F4PNM and F4PNR), but before I start cutting, I need to make sure I
I tried to order one from Tessco, but they have a $50 minimum order. 73, Dick, W1KSZ _______________________________________________ _______________________________________________ TowerTalk mailing
I want one also, but the minimum buy put me off. Since you and I make two, all we need is a third and we are golden. Anyone else want one ? I would be happy to act as conduit. 73, Dick, W1KSZ _______
I wouldn't be so cavalier about these tower sections ... after all, a 10' section of 25G weighs 40#. Now if the only thing holding it together is the rust, well, that's a different story. 73, Dick, W
I have a Rohn BPC45G Base Plate and Pier Pin and three GAR-30 Anchors that I have never used. They are available in Vail, Arizona (20m SSE of Tucson). If you have any interest in these contact me dir
I have the following, never used, Rohn 45 parts for sale: BPC45G Base Plate, with Pier Pin Three (3) GAR-30 Concrete Guy Anchors $225 the lot, BUT, you must come and get them. I cannot ship them. Sav
IIRC, adding guys to a crank-up that was not designed for them, can reduce the structural integrity, not enhance it. I would research your idea very thoroughly before proceeding. 73, Dick, W1KSZ ____
Another alternative is LMR-400UF, stranded center conductor like RG-8, but better specs. 73, Dick, W1KSZ _______________________________________________ ______________________________________________
I used a P5 CW card for my installation !! 73, Dick,. W1KSZ _______________________________________________ _______________________________________________ TowerTalk mailing list TowerTalk@contesting
Does anyone have the schematic for the Bird 4391 ? I don't find one in the manual. Hopefully it's not a state secret !! Tnx, 73, Dick, W1KSZ _______________________________________________ __________
Does anyone have a copy of the Installation Instructions for the Andrew 44ASP (UHF) Connector, or know where I can locate it ? Thanks, Dick, W1KSZ _______________________________________________ ____