See the selection chart (especially the UV resistance data) in this Panduit pdf: http://www.digikey.com/Web%20Export/Supplier%20Content/Panduit_298/PDF/Pandu it_CableTiesSelectionGuide.pdf?redirected
Hello, Am looking for one of the mast systems - either AB-577 or AB-621, in good condition. I am located in NFL, but can pay shipping or will consider pickup depending on location. Let me know if you
I also use the Idiom Press LED lights for my Astron supply meters. --Ed-- -- This email is free from viruses and malware because avast! Antivirus protection is active. http://www.avast.com __________
Hello, I am looking for some military mast parts to buy: 1. AB-621 top piece 2. AB-621 winch with handle 3. AB-577 winch handle only 4. AB-621 middle guy ring. Thanks for any help. --Ed-- -- This ema
Hello, Looking to buy a middle guy ring for the AB-621 mast. Also looking for a 621 winch/handle. --Ed-- -- This email is free from viruses and malware because avast! Antivirus protection is active.
Hello, Has anyone on the list ever tried to design or build an assembly that would clamp on the top of an AB-577 or AB-621 mast and provide for mounting of a thrust bearing, perhaps about a foot abov
I looked at the Hubbell link Shawn provided on the earth anchors, and noticed this: Note: If hand installed, holding capacity may be reduced by as much as 10% to 20%. Capacity ratings apply to proper
Hello, I have the following AB-621 parts for sale: two launchers, AB-621A/G, in good shape. These are the seldom-seen square top versions with the one-inch drive. These launchers would make a good so
Hello, Looking for AB-621 top pieces and upper guy rings. Thanks for any leads. --Ed, N3CW-- -- This email has been checked for viruses by Avast antivirus software. https://www.avast.com/antivirus __
I have one set of guys on my 60 ft tower where the two turnbuckles for the mid and top guys are about at their maximum limit. There is maybe an inch of thread left to make adjustments on each of the
Hi Ron, How long is your rotator control line? What size wire do you use? Where is the motor start capacitor located (typically it is in the control box). How old is the capacitor? Any chance of varm
Jim, See: https://www.windy.com/ Not exactly right at your antenna but still useful info when you zoom in. --Ed, N3CW Sent from Mail for Windows 10 -- Message: 10 Date: Mon, 25 Feb 2019 19:17:42 -050
Hello, Has anyone on the list ever successfully shunt-fed an AB-621 military mast? --Ed, N3CW -- This email has been checked for viruses by Avast antivirus software. https://www.avast.com/antivirus _
HI Folks, I have a couple of old Top Ten Devices relay boxes; no model number or id is visible on the box. They allow for switching up to 6 different antennas. I do not have, and cannot find any
HI Les, Yes sounds like the same box. It appears it originally was meant to work with the TTD band decoder, and not an independent control head. I like the idea of switching the diodes...then I can u
Pete - take a look at this approach: http://www.seed-solutions.com/gregordy/Amateur%20Radio/Experimentation/RotatorCage.htm I've never tried it; not sure how well it worked. --Ed, N3CW-- Message: 1 D
Hi Pete, See if this one from Amazon might work: https://www.amazon.com/SZJELEN-2Pin-12Pin-Waterproof-Electrical-Connectors/dp/B07YWKNMGH/ref=psdc_172544_t3_B07DL2VHBQ?th=1 --Ed, N3CW-- -- Messa
GM Folks, Early this year I had a T2X rebuilt by a highly respected rebuilder. Part of the rebuild included new brake wedge, wedge dowel, return springs, and lower T2X/brake housing. All checked