I think you should consult with a PE before installing anything on this type of building. It just too many different design problems I can see. I think it be cheaper just to install a new base and th
Call Portland Bolt http://www.portlandbolt.com/ and they ship what ever you want and like all these outfits they make them and either in house Galv. them or send out . Also go to http://www.thomasnet
Sorry didn't answerer a bit sooner but been busy with a Rohn SSMW and we just poured a 18x4 and the cont. dug a Secord hole with a trench and pumped the water out and poured 55 yards. Worked real sli
The new NEC code requires Radio Towers ( It not related to any particular service to be bonded and grounded. Wither your code official is up to speed is a matter of where you are. Because my Matt fou
Take a pick and check to see if there is a hole into the bearning itself. I have seen more than once a sealed bearing and no place for the grease to go. That might be the reason there was no zerk on
My plastic owl is up for loan. It always finds True North. 73 Gene K2QWD -- Original Message -- From: "Dino Darling" <dino@k6rix.com> To: <towertalk@contesting.com> Sent: Monday, November 10, 2008 6:
The secrete to my plastic owl is it's a American made model very hard to find since the mold was hijack by a oversea maker and their model can't find north from south. It's a common complaint from fa
The rotator will set in a cage approximately 20 feet from the thrust bearing until it drives a 20 ft section of 2" Chrome Molly Mast that will hold approximately 30 Sq. ft of antenna's. SC coastal lo
It looks like a very nice tower series but if the conversion I did on wind speeds are correct from there web site they are limited to the 70 MPH noose that around most crankup necks. With the eastern
I agree with your excellent subjection of the Geologist but correct me if I'm wrong you still going to need a PE to design the base for the condition's that are found. I've personally use Hank Longbe
Instead of me going into one of my long winded explanation go to this website and the information is first rate and best FREEEEEE. Search there site under Radio towers and it's all there and being a
I remember some years back about a rf cable being made for audio work. I don't remember the particulars but it had to do with high end. I removed all the pl259 from them and reused them. (I know it b
No Ryan is right on all accounts. These were used on ladders on buildings long before the Tower industries used them and were part of CA code before our own. We call it Peter Pan around our shop and
Safety Harnesses come in a lot of different styles and as such some do not have side D ring. That being said if you are hooked to your side rings and are hooked to the fall cable's facing forward it
Good One Dale... ____________________________________________________________ Best Weight Loss Program - Click Here! http://thirdpartyoffers.juno.com/TGL2141/fc/BLSrjpTFoYdzLu8LSfmNtPFTFmCaq27n qL6N8
OSHA will have a field day with this and my thought to the man family. I just had my refresher class on these class machine's and interesting one point the instructor keep going over way walking the
First, I have received the new Rohn catalogue and I have given it a quick look, and I do think, Steve, that it will have some value as my recent experience over the last few years have been in the Co
Do you need the manual I have the one for the last run of them. Senf Phone number and I'll tell how to do the cage. Gene K2QWD Hi Ron, I have one of those towers to put up this summer (hopefully). Di
Look at the relays and the timers real chose and note direction that the screws are installed in the pull out bases. The screws if installed in wrong direction holds them out just enough so the pins
Funny that this subject has so many sides when for years I used a small Telex/Highgain tower that used a pair of brass plates with groves machined into them. Now no lube and no bearings. It was used