Mail Archive Search: <+from:hasben@ix.netcom.com>

Results:

References: [ +from:hasben@ix.netcom.com: 14 ]

Total 14 documents matching your query.

1. [Towertalk] Prop-Pitch (score: 1): Author: hasben@ix.netcom.com (Richard Hassell-Bennett); Date: Sat, 1 Jun 2002 15:43:25 -0500; There is Prop pitch for sale on ebay. See below. http://cgi.ebay.com/ws/eBayISAPI.dll?ViewItem&item=1356129041 I also believe M^2 may have some available. de Richard K0XG; /archives//html/Towertalk/2002-06/msg00009.html (7,896 bytes)
2. [Towertalk] Coding on Bolt Heads? (score: 1): Author: hasben@ix.netcom.com (Richard Hassell-Bennett); Date: Tue, 11 Jun 2002 05:54:18 -0500; Eric. Take a look at http://www.unified-eng.com/scitech/bolt/boltmarks.html See if that is what you want. 73 de Richard K0XG www.k0xg.com -- Original Message -- From: "Eric Rosenberg" <wd3q@erols.com; /archives//html/Towertalk/2002-06/msg00136.html (8,741 bytes)
3. [TowerTalk] What is a good way to rotate a tower? (score: 1): Author: hasben@ix.netcom.com (Richard Hassell-Bennett); Date: Wed, 29 Aug 2001 06:32:35 -0500; Best way to do this is with a RoTek bearing. BUT....... the cost of the bearing and the cost of the concrete would far exceed the cost of guy bearings and guy wires ..... de Rich K0XG www.qth.com/k0x; /archives//html/Towertalk/2001-08/msg00643.html (9,217 bytes)
4. [TowerTalk] Tape and wxproofing (score: 1): Author: hasben@ix.netcom.com (Richard Hassell-Bennett); Date: Mon, 9 Jul 2001 11:35:26 -0500; Fully agree with Steve. "the right tape and right technique" That is why 3m makes #70 tape. Use #70 and then cover it with #88 and it will last a life time. 73 de Rich K0XG tape 88. List Sponsor: Are; /archives//html/Towertalk/2001-07/msg00153.html (8,111 bytes)
5. [TowerTalk] antenna mounts (score: 1): Author: hasben@ix.netcom.com (hasben); Date: Wed, 6 Jun 2001 17:05:25 -0500; Hi Bruce, We manufacture Boom to Tower plates and Boom to leg mounts just for this application. Have these available for 2", 3" and 4" booms, and for Rohn 25,45,55, 65 and 80. If you need to offset t; /archives//html/Towertalk/2001-06/msg00084.html (9,106 bytes)
6. [TowerTalk] Galvanized Hardware (score: 1): Author: hasben@ix.netcom.com (Richard Hassell-Bennett); Date: Mon, 11 Jun 2001 07:56:31 -0500; Try Stan W7NI@easystreet.com de Richard K0XG www.qth.com/k0xg for BIG tower hardware and fixtures Rohn-like galvanized hardware other than Rohn itself? are used around tower legs to hold some custom; /archives//html/Towertalk/2001-06/msg00214.html (8,882 bytes)
7. Fw: [TowerTalk] Cleaning connectors (score: 1): Author: hasben@ix.netcom.com (Richard Hassell-Bennett); Date: Wed, 2 May 2001 10:43:12 -0500; Best thing I have found is Coca Cola !!!!!!!!!! Leave them to soak overnight then change the Coke and leave them all day, maybe do it a 3rd time in Coke. You will need to wash the Coke off with warm; /archives//html/Towertalk/2001-05/msg00053.html (9,058 bytes)
8. [TowerTalk] T2X and the Ring Rotor Control Box (score: 1): Author: hasben@ix.netcom.com (Richard Hassell-Bennett); Date: Sun, 8 Apr 2001 14:50:21 -0500; Hi Nat. FYI The T2X box is designed to run an AC motor, while the Tic box is designed for a 24VDC motor. Feed back for position on both rotors is via a 500 ohm potentiometer. You could make a box wit; /archives//html/Towertalk/2001-04/msg00180.html (10,824 bytes)
9. [TowerTalk] Marking Coax Cables (score: 1): Author: hasben@ix.netcom.com (Richard Hassell-Bennett); Date: Fri, 2 Feb 2001 10:17:10 -0600; Scotch 35 tape comes in multi colors for marking electrical cables. Just add some clear shrink tube after and it will last for years. Even the cheaper tape will be ok if you shrink wrap it after you; /archives//html/Towertalk/2001-02/msg00055.html (10,289 bytes)
10. [TowerTalk] mast intrusion into tower (score: 1): Author: hasben@ix.netcom.com (Richard Hassell-Bennett); Date: Sat, 13 Jan 2001 21:54:09 -0600; AL. If you buy a single guy ring and one of our elevated rotors you can rotate 50ft of tower (20' below and 30' above the guys). for about the same cost !!!! Take a look at www.qth.com/k0xg Something; /archives//html/Towertalk/2001-01/msg00341.html (9,082 bytes)
11. [TowerTalk] 4 point guying...how? (score: 1): Author: hasben@ix.netcom.com (hasben@ix.netcom.com); Date: Fri, 2 Apr 1999 17:04:38 -0600 (CST); Hi Gary, Trying to get the "Short guy Equalizer" balanced would be absolutely impossible. The best method is as Steve said....... Put two guys on one point of the guy bracket (use three shackles) the; /archives//html/Towertalk/1999-04/msg00028.html (9,324 bytes)
12. [TowerTalk] Galvanized hardware questions (score: 1): Author: hasben@ix.netcom.com (hasben@ix.netcom.com); Date: Fri, 19 Mar 1999 21:45:18 -0600 (CST); Hi Pat, Under no circumstance would I use grade 2 bolts for any application on any antenna or Tower. If you cannot find what you want, send me an e-mail as I have parts Hot Dipped quite frequently, a; /archives//html/Towertalk/1999-03/msg00379.html (10,083 bytes)
13. [TowerTalk] Guy Ring Bearings (score: 1): Author: hasben@ix.netcom.com (hasben@ix.netcom.com); Date: Sun, 13 Jul 1997 21:07:50 -0500 (CDT); During the comming week, I will be ordering parts for the manufacture of some "Heavy Duty" Guy ring bearings, for use with Rohn 45 and 55 rotating towers. Some of the bearings will be for my use, and; /archives//html/Towertalk/1997-07/msg00478.html (7,030 bytes)
14. [TowerTalk] Stainless Steel Hardware (score: 1): Author: "Richard Hassell-Bennett" <hasben@ix.netcom.com>; Date: Tue, 20 Apr 2004 11:44:02 -0500; Here is an interesting website for those looking for Stainless Steel hardware. www.jschmidtstainless.com/products.htm De Richard K0XG Richard Hassell-Bennett hasben@ix.netcom.com www.K0XG.com _______; /archives//html/Towertalk/2004-04/msg00380.html (7,424 bytes)

Current List: 1 - 14
Page: [1]