I never climbed a tower in my life. I don't even like ladders. When I saw that rubber covered tower rung in QST I felt the same way. It sure looks dangerous to me!!! 73, Ted K2QMF ___________________
This link doesn't work either... Ted K2QMF ________________________________________________________________ GET INTERNET ACCESS FROM JUNO! Juno offers FREE or PREMIUM Internet access for less! Join J
This works great!! Many Thanks... 73, Ted K2QMF List Sponsored by AN Wireless: AN Wireless handles Rohn tower systems, Trylon Titan towers, coax, hardline and more. Also check out our self supporting
Hello All, We have an LM-354 purchased new and installed about 4 years ago. The tower is a manual crank-up. The tower has always been very hard to crank up and down! You have to stop half way up to r
Hi George, Alignment seems good and there is no noticeable scraping sound. We have a 15 foot mast with a TH-5 at the top and a Cushcraft 2 el 40 ten feed below that. Maybe that's the reason it is so
Hello again, Is it okay to paint a rebar cage before putting it in the ground and poring concrete over it??? Thanks for the information. 73, Ted K2QMF ________________________________________________
Hello again All, I am looking for some help / suggestions on the best way to dig a 4 by 4 by 8 foot deep hole for my new tower base. Is the old Armstrong method best or would a backhoe be best?? Will
Hello All, I'm not sure if this is the correct reflector for my question but here goes... Can anyone tell me what is involved in replacing the screw terminal board on the bottom of the Ham-4 rotor???
Hello All, I am in need of a copy of the Engineering Drawings for either a Tri-Ex LM-354 or Tri-Ex W-51 crank-up tower... If anyone has or can make a copy I would be happy to pay any expenses. Thanks
subscribe ________________________________________________________________ The best thing to hit the internet in years - Juno SpeedBand! Surf the web up to FIVE TIMES FASTER! Only $14.95/ month - vis
Hello All, I am getting ready to install my new LM-470 Crank-up tower. I was wondering if there is any problem pouring concrete for the foundation in cold WX. Like below freezing??? Any information w
With all this response to this cutesy site, I am sorry that I missed it!!! Can someone please give me the site address again?????? Thanks in advance and 73, Ted K2QMF ________________________________
Hello all, The plans for an LM-470 base call for a hole 3.5 X 3.5 X 7.5 Feet deep. (Aprox 3.4 yards). My question is, would a hole 4.5 X 4.5 X 7 Feet deep (Aprox 5.3 yards) be acceptable even though
The M2 OR-2800 is a great rotator. Just Check the specs. Also, service from M2 is outstanding... 73, Ted K2QMF P.S. - Make sure you get the new version with the green readouts.. Has all the updates.
Hi Tony, I don't know about the older version however, the new or-2800 is very easy to program... 73, Ted K2QMF ________________________________________________________________ The best thing to hit
How come, No one mentions "Zero Rust". I have used zero rust and it works great... 73, Ted K2QMF On Sat, 27 Mar 2004 23:55:44 -0500 "Joe - KC2TN" <kc2tn@comcast.net> writes: _________________________
Hello All, Everyone should make a comment regarding the NPRM from the FCC It is very easy to do.. go to http://gullfoss2.fcc.gov/ecfs/Upload/ Make sure you use a capital U in Upload/ It is very easy.
Hello All, Everyone should make a comment regarding the NPRM from the FCC It is very easy to do.. go to http://gullfoss2.fcc.gov/ecfs/Upload/ Make sure you use a capital U in Upload/ It is very easy.
Another good reason to NOT vote for Bush............ ________________________________________________________________ The best thing to hit the Internet in years - Juno SpeedBand! Surf the Web up to