Jim How would one "bond" a metal roof joint? The joints crimped together all along the joint? Thanks 73 Kent N6WT _______________________________________________ _____________________________________
Phil I considered the BigRak for my HDX572. My concerns were it would not fit completely inside the tower like you. My biggest concern was tilting the tower over to work on the antenna. With the top
I take that back, I had one small problem. The mast clamp on the Orion rotor is a bad design and allowed the mast to slip. I replaced it with a clamp from KF7P Metal Werks. All FB now! Thanks 73 Kent
Ok Im sold! Im glad I went with the M2 Orion! Thanks 73 Kent N6WT _______________________________________________ _______________________________________________ TowerTalk mailing list TowerTalk@cont
ThaI did both! The Green Heron works great! 73 Kent N6WT _______________________________________________ _______________________________________________ TowerTalk mailing list TowerTalk@contesting.co
Thats the one that I used. Not sure why I thought it was KF7P?? Thanks 73 Kent N6WT _______________________________________________ _______________________________________________ TowerTalk mailing l
Jim The mast clamp on mine slipped after 6 months. I took it down and tightened the bolts again with blue thread locker this time and 4 months later it slipped again. I think the the problem is I use
Well not sure what to tell ya. All I know is Steve K7LXC says he see them slip all the time and mine did. Thanks 73 Kent N6WT _______________________________________________ _________________________
Jim No one is calling you a liar. I may call you lucky. 73 Kent N6WT _______________________________________________ _______________________________________________ TowerTalk mailing list TowerTalk@c
Google is your friend! https://www.google.com/search?q=split+loom+tubing Thanks 73 Kent N6WT _______________________________________________ _______________________________________________ TowerTalk
Bob I was told that the Big RAK would fit in my HDX572 but it would stick out. If you lower the tower all the way it will hit the top of the second section. I went with an M2 Orion 2800 with a Green
That being the case I'm glad I went with the Orion. I have a SteppIR DB36 and have never had a problem. Kent N6WT On Wed, Dec 19, 2018, 19:07 Richard (Rick) Karlquist <richard@karlquist.com wrote: __
As far as the M2 Orion 2800. It got a bad rap because they had a bad batch of gears, that is why it has a low rating on eHam. The problem has now been fixed and I think it is the best. Just my 2 cent
I finally had to give up and used poison. I live out in the country and they were into everything, kitchen, pantry, laundry, motorhome and etc. There is a website domyown.com. I found out the best st
When I installed my US Tower HDX 572, I dug down 3 feet and found sand stone. I called a neighbor with a backhoe. He dug until it broke. I was within a foot of where I had to be. I rented an electric
I have 16 acres and have to mow 8 of them. The pasture I mow with a tractor. When I get close to something like my tower I use a weed whacker. That being said I have done unintended damage with the w
Rick What leads you to believe that he was using a remote to crank the tower up and down? 73 Kent N6WT _______________________________________________ _______________________________________________
John I would not do it but you milage may vary. Thanks 73 Kent N6WT _______________________________________________ _______________________________________________ TowerTalk mailing list TowerTalk@co
I love my M2 Orion 2800 with Green Heron controller!! I did replace the mast clamp and all is well!!! Thanks 73 Kent N6WT _______________________________________________ _____________________________
Fritz When the tower stalls, does it blow the circuit breaker?? I had a problem with my HDX572. It was a bad electric motor. Every time I would raise the tower it would blow the fuse (yes, there is a