https://www.stafix.com/en-us/product/heavy-duty-claw-joint-clamp martin W2RWJ Bob K6UJ There seem to be some other varieties of these clamps, but individually the are expensive. Any USA sources or ot
Working on a project that may be called into service for AMSAT Phase 4. Before I hire someone for the geotechnic portion, I wanted to gain the insight of TT. Antenna is a 12' solid surface dish, with
http://www.cosmtec.com/products.asp?Page=3&pname=N+RF+Connector&pfid=4&flev=2&puid=14&N+RF+Connector.htm Martin, W2RWJ Martin, HS0ZED On 10/01/2018 09:33, Paul Christensen wrote: Owners of the VNA218
are you using ? What brand DIN and what cable is the male attached to ? I have not had any issues with inter series connectors either, like din male to type N female.... or a 7-16 din double male, or
Doug, Crosby sells spelter sockets and epoxy kits https://www.thecrosbygroup.com/products/sockets/spelter/mckissick-416-open-spelter-sockets/ They show up on the big auction site for under $50 each.
Valve tags: http://identificationtags.com/valve-tags.aspx? as an example 73 Martin W2RWJ Tried colored tape (including the best 3M) but found it fades after a short period (like a year) exposed to m
Might be overkill, however I have seen a replacement coupling nut for a PL-259 made out of 18-8 hex bar stock. Martin W2RWJ On 2/24/2019 1:03 PM, Grant Saviers wrote: Nice to have a strain relief, bu
Take a look at this: https://hackaday.io/project/10489-powerpole-distribution-block Would not be a major issue to scale this to 4 conductors. As KZ1W noted, the connector shells can be had in colors
https://www.mcmaster.com/spade-bolts/ Spade bolt maybe? On 8/14/2020 7:31 PM, Joe K2UF wrote: I'm looking for a hardware part. I don't know it's name. They used to use them a lot in Heathkits. It is
On 9/4/2020 11:10 AM, Bryan Fields wrote: On 9/4/20 10:34 AM, mike stokes wrote: Looking fo recommendations on a pan, zoom, tilt outdoor camera to put on my tower. I have 10 acres and would like to k
Subject pretty much covers it - I Need 250 feet of 5/16 EHS, no need to buy a 1000 reel for a one shot project. Suggestions on where to buy? _______________________________________________ __________
Anyone have used TA55 torque arms for a Rohn 55G tower (18-1/2" CC) ? Looking for fours sets on a limited budget. 73 Martin W2RWJ _______________________________________________ ____________________
Does your municipality have a setback ordinance (no structures within "X" feed of the property line)? If so, perhaps appearing at the Zoning committee meeting demanding a variance that runs with you
Search for Amp pidg terminals Solistrand Sent from my iPhone _______________________________________________ _______________________________________________ TowerTalk mailing list TowerTalk@contestin
Ted, I'm hoping that's humor... .....As to the advanced practice, bring it on! Martin W2RWJ On 1/21/2022 1:54 PM, Salvatore ["Ted"] K2QMF wrote: Wow, All this Epsilon, Lambda, Sigma, and e" and e" st
Before I re-invent the wheel, anyone aware of a 75 ohm version with an F connector? 73 Martin W2RWJ _______________________________________________ _______________________________________________ Tow
All depends on the your budget - I'm using a Vaisala WXT series sensor. Communications are serial over 800+ feet of (well grounded and surge suppressed) cable Speaks RS-232,RS-485, RS-422, and SDI-1
Any suggestion on the correct thimble size and nicopress (compression) sleeve that would be used with #14 and #12 Flexweave? Martin W2RWJ _______________________________________________ _____________
or burndy C-tap since they are rated for copper, and the nicopress are not.... Martin W2RWJ _______________________________________________ _______________________________________________ TowerTalk m
Similar experience - I use a Pasternak PE5011-1 click wrench on SMA connectors and not have issues with a connector loosening. 73, Martin W2RWJ On 12/4/2022 5:27 PM, Gary NA6O via TowerTalk wrote: Iv