Is that 3m 103C or a different 3m product? Mark N1UK I now use 3M splicing tape instead of CoaxSeal. It seals great and is easily cut to remove it and it does not leave the gooey and sticky residue.
I saw on some guy's QRZ page his lowering method. He had an outside camera monitoring his crankup tower. The camera output went through an A/B switch to his pc monitor, so that he could monitor the t
Belling-Lee is a coax connector that is fitted to the antenna input of English tv sets http://en.wikipedia.org/wiki/TV_aerial_plug _______________________________________________ ____________________
Yes Moss Motors sells waxoyl over here http://www.mossmotors.com/Shop/SearchResults.aspx?SearchText=waxoyl&WebCatalogID=0 I put it inside my 1989 Blazer chassis and hand brushed it on the underside w
ehs cable is so cheap, why risk it. Are you installing 2 sets of guys? I believe that is in the Rohn spec for a Rohn 25 tower at your height. Are you using the guy brackets to connect the guys to the
Yes it was a joy pulling my phillystran top guys up my 86 foot Rohn 45 tower, so are so light and quick to make instead of all that messing around with insulators which I did for the lower set of guy
I just put a little snip in the carpet and drilled a hole through the wooden floor and pushed the coax and PL259 through the hole. In fact I have several holes through the floor of the shack into the
The wireman sells the cable for the Orion rotator. It has a thick black and a thick white wire for the dc motor and then has a shielded set which are wrapped in foil. Inside the foil is a bare drain
Sorry to hear about your tower, That really sucks. It is even a bit blowy here in North Carolina today. What tower did you have? Mark N1UK _______________________________________________ ____________
I use my camera for jobs on the car, such as drum brakes with all those springs and fittings Mark N1UK _______________________________________________ _______________________________________________
Here is the 25AG section http://www.3starinc.com/rohn_25g_top_cap_tower_section_r-25ag.html I have a similar 3 foot section and my Ham IV fitted in there fine. Mark N1UK -- Original Message -- From:
I think that it will be fine. It is a guyed tower and the base is just to stop the tower sinking into the ground. Mark N1UK _______________________________________________ ___________________________
Here is the Rohn 25 that Gene wanted to share with the group. Click on the link to download the PDF file http://www.mediafire.com/file/qv0fn5elro93bgo/Rohn%2025G.pdf 73 Mark N1UK Last try at sending
When I assembled the Phillystran guy wire assemblies on my recent Rohn 45 tower I used the big grips that are made specially for the phillystran cable. This is the preferred method of terminating the
Looks like they make big grips for the 1/8 philly HPTG 2100I (big grip part number PLP-2738) but not for the 3/32 equivalent Mark N1UK _______________________________________________ ________________
Good to hear this. I am fed up with not knowing the specifications of imported cheap foreign "junk" When it fails we have no come back. Mark N1UK Now that you are all rested from SS -- I received thi
I have just installed the OR2800 on my tower. I used the shielded control cable that the wireman sells. This wire has a heavy awg pair of wires (black and white) for the DC motor supply. It also has
Is there any advantage in connecting a grounding loop between the mast and the adjacent tower leg? Mark N1UK _______________________________________________ __________________________________________
There are bushings available to go inside the Rohn top section http://www.3starinc.com/rohn_25ag_45ag_section_tower_bushing_r-tb50.html http://www.3starinc.com/rohn_25ag_45ag_section_tower_bushing_r-