Mail Archive Search: <+from:n1eu@yahoo.com>

Results:

References: [ +from:n1eu@yahoo.com: 8 ]

Total 8 documents matching your query.

1. [TowerTalk] Hy-Gain rotor controllers cabling (score: 1): Author: Barry Gross <n1eu@yahoo.com>; Date: Tue, 19 Oct 2010 04:30:36 -0700 (PDT); Can anyone confirm that rotor cable connection pin numbering 1-8 of a T2X terminal block is identical to pin numbering 1-8 of a Ham IV cinch Jones connector? Tnx/73, Barry N1EU ______________________; /archives//html/Towertalk/2010-10/msg00219.html (6,561 bytes)
2. Re: [TowerTalk] Hy-Gain rotor controllers cabling (score: 1): Author: Barry Gross <n1eu@yahoo.com>; Date: Tue, 19 Oct 2010 07:23:29 -0700 (PDT); I've received several private replies that indicate folks aren't aware that Hy-Gain was installing rear panel mount 8-pin Cinch Jones connectors in the later Hy-Gain Ham IV rotor controllers instead; /archives//html/Towertalk/2010-10/msg00220.html (7,509 bytes)
3. [TowerTalk] Ham IV rotor reassembly (score: 1): Author: Barry Gross <n1eu@yahoo.com>; Date: Fri, 29 Oct 2010 15:56:52 -0700 (PDT); I seem to be stuck at the last step of a Ham IV reassembly and would appreciate any helpful advice. I've lowered the main assembly into the upside down upper housing and made sure the potentiometer a; /archives//html/Towertalk/2010-10/msg00412.html (7,025 bytes)
4. Re: [TowerTalk] Ham IV rotor reassembly (score: 1): Author: Barry Gross <n1eu@yahoo.com>; Date: Sat, 30 Oct 2010 03:35:00 -0700 (PDT); Thanks for many responses suggesting one of the bearing retainers might be upside down. I carefully installed them with the flange away from the central rotating race. But the suggestion does make se; /archives//html/Towertalk/2010-10/msg00413.html (9,124 bytes)
5. Re: [TowerTalk] Ham IV rotor reassembly (score: 1): Author: Barry Gross <n1eu@yahoo.com>; Date: Sat, 30 Oct 2010 06:07:33 -0700 (PDT); I disassembled and checked - bearing retainers were correct. I posted photo series showing the reassembly: http://n1eu.com/ham4.jpg If there are any experts out there, perhaps you could comment on th; /archives//html/Towertalk/2010-10/msg00414.html (11,122 bytes)
6. Re: [TowerTalk] Ham IV rotor reassembly (score: 1): Author: Barry Gross <n1eu@yahoo.com>; Date: Sat, 30 Oct 2010 08:13:33 -0700 (PDT); I achieved success thanks to several helpful emails - I had the races ass backwards (i.e., races aren't necessarily those smooth polished surfaces). Tnx/73, Barry N1EU I disassembled and checked - be; /archives//html/Towertalk/2010-10/msg00415.html (11,493 bytes)
7. Re: [TowerTalk] Ham IV rotor reassembly (score: 1): Author: Barry Gross <n1eu@yahoo.com>; Date: Sat, 30 Oct 2010 14:16:04 -0700 (PDT); (it's after the fact - all has been sorted out) First you want to identify the races (the surface the ball bearings ride on) and then you want to orient the retainers such that the flanges are facing; /archives//html/Towertalk/2010-10/msg00419.html (7,718 bytes)
8. Re: [TowerTalk] Ham IV rotor reassembly (score: 1): Author: Barry Gross <n1eu@yahoo.com>; Date: Sat, 30 Oct 2010 19:02:15 -0700 (PDT); What the emails all basically said was that the bearing retainer flanges should be oriented toward the center of the rotor. If you look at the middle photo of http://n1eu.com/ham4.jpg , you're looki; /archives//html/Towertalk/2010-10/msg00424.html (13,862 bytes)

Current List: 1 - 8
Page: [1]