I have the Article and can send... Your QRZ.com address OK ? 73, Dennis N6KI _______________________________________________ _______________________________________________ TowerTalk mailing list Tow
...And don't forget, you don't get ALL the parts with your antenna kit, especially some of the critical ones, even after many phone calls... Then, F12 will tell you how to go to home depot to make yo
...and if it is the well known "Stuck at end of rotation " problem, once you get it going again, do yourself a favor and buy a kit from IDIOM Press that allows you to turn the antenna to a selected A
One think for sure...A Japanese company selling out to an American company... Quality etc is likely to go downhill, haven't seen a Motorola product I much care for especially their crappy cel phones
*My question is, what spec should one be looking for in the solder plate either by material like nickel or silver or some spec in order to get connectors that are solderable ! ( Obviously silver work
Talk to the guys that repair them for a living, just like one would research a car Suggest you contact Norms and C.A.T.S. , a Google search should lead you to them let them tell you how wonderful the
Per my article on using non corrosive and non UV RTV for rebuilding traps on Telrex Yagis I can recommend Dow Corning 738 http://www.ac6v.com/telrex.htm It only has a 6 month storage shelf life so yo
Yes, the Homing/Calibration procedure highly recommended but you did not mention, are there any other antennas near the steppir, metal roof sheds etc etc ? Assuming U still have same problem after yo
You can call RF Industries in San Diego ( It used to be called Worswick and RF Industries bought the company when owner retired ) http://www.oddcables.com/ They will make ANY cable you want if you wi
I have a LM-470D tower that was manufactured in early 1980s Here are the specs on it's motor Dayton Model 6K122D 1/2 HP 1 Thermally Protected 1725 RPM 15/230VAC FLA 9.0/4.5 The Motor Start Capacitor
KLM is long since put of business and I guess M2 handles rebuild kits but may not know the info you need _______________________________________________ ______________________________________________
Joe, I don't have this specific answer about the sealant you need, but when you finally get the antenna working and installed be very careful applying more than 200 watts to this antenna on any freqs
I would Google H H Smith Company or Pomona as 2 of the most usual suspects that might carry such an adapter/connector Also try Mouser Electronics, Digikey or Newark Electronics and then there is Mc M
Well even some of the Amphenol PL-259 connectors are hard to solder to. Have been buying this easy to solder Amphenol P/N PL-259 lately from Mouser Electronics ( I am sure other vendors carry them )
The 2800 mast slip problem is well known here is a piece pof thread from provious discussion TowerTalk mailing list TowerTalk@contesting.com http://lists.contesting.com/mailman/listinfo/towertalk The
Dick, Marshall's Hardware in San Diego near me and great place to deal with If U need me to go and look at the rivets or verify anything about them before U order let me know Marshall's can be reache
Can anyone tell me the EXACT O.D. and I.D and length of the short section of Tubing that is used at the top of the AB-577/GRC Mil Tower Kit which many hams have purchased om the Military Surplus mark
The thing you might want to do is employ a P.E. (Professional Engineer) to do the calcs for you that tells you what heights on your particular tower yields a safe wind load for you situation. I am re
Contact Terry N6CW in San Diego who is handling an estate sale where there WERE many Rohn 25 tower parts and I saw some misc parts laying around the estate qth a few days ago..maybe U will get lucky
...and this is why.....TV is called ..... The "Moron-O-Scope" Now back to my DVDs....... ( Ok, so I do watch the Liberal slanted PBS now and then ) N6KI On Sun, Jul 20, 2008 at 9:09 AM, Tom Osborne <