these guys will take care of you Atlantic Bolt, Inc. Charlotte, NC 28206 704-597-5082 Dan N8DCJ I will be installing a HG 70 HD this summer and I am looking for anchor bolts. I am having some trouble
After the recent grounding discussions , last night during a thunderstorm I was thinking about how to go about grounding/lightning protection. Here is the basic setup , UST TX-472 , with PRO57B , Inv
I am going to re-cable the tower this summer , I am not at all comfortable with some sections of the cable. Where is the best place to get the cable , and does anyone know just how much cable I need
Ok , I have most of my ground system planned out , my plan is to use copper pipe (type "L") and silver solder flashing to them from the tower etc... my issue is how in the world do you guys drive cop
I have a DXEngineering radial plate , they suggest using ring terminals , it seems to me that if you solder them , if , you taker a lightning strike the solder would all be vaporized ? Should I just
Mark I guess I left something out , the plate will also tied to the tower at the base and the entire grounding system , from the reading I have been doing , if , I should take a strike the radial fie
Ok , now on to my next question , what is the best way to lay these radials down using my riding mower ? As I will be running at least 5000 ft of radials anywhere from 75ft to 200 ft long I would lik
I need to replace the main lifting cable on my TX-472 (it is badly rusted and flattened out , the others are fine) , I can get one from UST for about $170 and 3-4 weeks. Experience tells me I should
Glen call these guys they will make whatever you need... http://www.atlanticboltinc.com/ when i needed bolts for my TX472 they were cheaper than anywhere else... Dan N8DCJ __________________________
By chance does anyone have a Fulton K2550 0301 winch they wish to part with ? I need one for the raising fixture on my TX-472 Thanks Dan N8DCJ _______________________________________________ ________
"3. forging return or reply-to address - " I currently have this one happening , they even send them to me so I get to see them , at least I know what "I" am trying to sell promote , hihi Dan N8DCJ
When my UST TX-472 was delivered it came on a flatbed , along with a much larger motorized tower that I tried to talk the driver into dropping off :-)... I had a tow truck in the driveway , he picked
I had to remove the terminal block on the bottom of the rotor , it was falling apart, i wrote down the wire colors as best as I could see them , does anyone have the internal pinout to the backside o
Ok , I have my Mosley PRO57B put back together and need to test it. It is currently only about 3 ft off the ground in the horiz position .... can I test it out this way ? Moving it to vertical to tes
I seem to have lost my mast pipe , and only have access to Homedepot , Lowes and such , I am only going about 1 ft above the top of the tower so I figure heavy water pipe should work. Does anyone kno
"The Mosleys would probably also benefit from decoupling the feedline shield with common-mode chokes (ferrite or coiled-coax) although the manual I saw during the test said not to use a balun for som
I am putting a replacement winch (K2550) on my TX-472 , I am not sure I have the correct bolts as I think I misplaced them. What I have is marked F593C THE , it is a 3/8-16 304 SS bolt , is this the
Les try Atlantic Bolt , when i put my TX-472 up they knew exactly what I was talking about , I faxed them the info I had from UST and in a couple of days I had my bolts in hand , about $200 less then
I have a cheap 1/2" drill that I tried on the tower raising fixture (TX-472), but , I can control it at a very slow speed. does anyone have a feel for how many rpm these winches can safely spin at ,
"those who have email addresses NOT on yahoo.com are bounced (you do NOT receive the message) while those with yahoo.com email addresses DO receive Tom's messages." This may not be entirely true ,