I have the 61, bought it at Dayton a few years ago. NO PROBLEMS HERE. I had 2 tailtwisters that failed, enough for me, and the Yaseu 1000sdx that the mast clamp broke and the unit could'nt handle a M
Mitch, I don't remember but they are thin to begin with. I bent mine pulling it out with a small dump truck. I replaced it with regular water/steam pipe, (sched 40) which was almost twice as thick .
I have one Rick NK9G Cudahy , WI (Milwaukee County) --Original Message-- From: Brian P. Mileshosky <n5zgt@swcp.com> To: towertalk@contesting.com <towertalk@contesting.com> To: <towertalk@contesting.c
I've had mine up about a year now and its works A1. I am rotating a PRO-57 at 50'. Mine is a PST61. I opted for the larger because I never want to replace a rotator again. It's mounted in a Rohn HDBX
Go to the WEB www.prosistel.com and it gives the dealers which i think is 2 I have a PST 61 and works fb, Rick NK9G Cudahy WI (Milwaukee County) --Original Message-- From: Jim Thompson - W3LAP <w3lap
I have that for my big boy ( PROSITEL) and it works GREAT! That probably would have saved my SDX-1000. NK9G Rick tower? http://www.anwireless.com List Sponsored by AN Wireless: AN Wireless handles Ro
RE: Yaesu 1000SDX. I've had 2 Tailtwisters and a Yaesu 1000 all failed. I have a Pro-57 and decided to go with the PROSISTEL Big Boy PST 61. So far so good. I hope this is the last rotor I ever have
Hi All... I have a E-Z-Way tower, 44' 2 sections and its 30 yrs old and it is in A1 condition. I had to repair about a third of the welds but since the initial repair its been a great tower and been
I use a R7 about 4' off a 100 X 100 steel roof and operate a fair amount of QRP DX with good results. At 100 watts I work most of what i hear....... with patience Rick NK9G --Original Message-- From:
Go to www.cushcraft.com and you can download the manual or just read it Rick NK9G --Original Message-- From: Bill Coleman <aa4lr@arrl.net> To: KB7WW Art Moe <kb7ww@chatusa.com>; towertalk@contesting.
I've had more tailtwisters than I want to think of, and 1 Yaesu 1000 If you want to save $$$$ over the long run get a PROSISTEL BIG BOY. I could have bought 3 of these for what I've spent on T2's and
I have a HDBX 48 and in fact have a spare... They are a lot str=onger than you think. Mine has a Mosley PRO-57 with a 220 repeater ant above it, above the tower some 20'. This thing has seen 70 mph w
Does anyone have info on the gears in a Prosistel PST 61. I've been a big fan of this until now! It's been up in a 48' Rohn HDBX tower with a Mosley Pro-57 and the gear box has seized .Motor works OK
correct me it i am wrong but on some you can change the pin configuration.. Check it out .. A local ham did so for a 1000sdx Rick NK 9G _______________________________________________ See: http://www
yes , I wrote it down item # 2082237 velcro wraps 50 for $3.99 Rick NK 9G Didn't somebody post a message yesterday about OfficeMax having a sale on Velcro wire wraps??? Larry K1ZW Durham, NC ________
Has anyone experienced a problem with water getting into the gearbox through the main shaft? I did... problem was a siezed bearing to race and no water evident in gearcase oil. Due to poor seal & POO
I had a Mosley Pro-57 with a 24' boom on mine for about 10 years. But to say I wasn't afraid the bugger wasnt going to come down is a under statement. I finally took it down since my Big Boy failed a
Has anyone homebrewed a rotateable dipole for 30 meters. I am looking to make a single band (30) shortened with some sort of traps. Any direction would be appreciated. Thanks Rick NK 9G _____________
Anyone know of a good source? Rick NK9G _______________________________________________ _______________________________________________ TowerTalk mailing list TowerTalk@contesting.com http://lists.co