Anyone know of any used towers for sale in NY and Long Island area. Also looking for a yagi. Tks, Ron _______________________________________________ _______________________________________________ T
I was thinking of replacing my old KT34 with A Tennadyne T-6. Any opinions on it. it would only be at 40 feet. Do they tend to have good swrs across all bands? Are they tough to adjust? Tks, Ron ____
Are we allowed to put towers and antennas for sale or wanted items here? Not commercial ads. Just ham to ham. Tks, ron _______________________________________________ ________________________________
A friend of mine is semi retiring from doing tower installations. Makes me feel old to say that. He has several antennas to sell to make room now. Allin good condition and he will professionally pack
My friend has 2 beams for sale: Mosley PRO 57 excellent condition, very rugged, professionally boxed and labeled for easier assembly. $490 plus shipping. Force 12 C3ss 6 elements , 12 foot boom , $48
I'm thinking of replacing my old KLM KT34a. I need a somewhat low profile antenna, not too big. Thinking 2 el Steppir or Tennadyne T6. I'd like opinions of the 2 element Steppir versus the T6 Tennady
I have a Force 12 C3ss in very nice condition . Good for small footprint. $390 plus shipping from NY or pickup. Please contact off list at: ryoung158@gmail.com Tks ___________________________________
My buddy has a Tic Tac 1032c ring rotor, with the AC4140 truss brace and ac 4200 leg insert in good condition(no rust) , with paperwork. Original cost was $1500. This is the big one that can handle R
I havean MARB with the 40 footer. The entire tower turns. I use a Tailtwister but the HamIV would have been fine. The beauty is the rotor is at ground level if you need to get at it. The rotor is at
Have the following for sale for a friend : T2X $295 Ham IV $245 T2X rebuilt with stainless $325 Yaesu 450 $125 all with control boxes Also have tower mast mounts: for: Tailtwister $35 Ham IV $25 Ham
I have, from an old antenna, where Penetrox was not used, am aluminum tube stuck inside another slotted tube. It is frozen tight. I sprayed some Liquid Wrench, but that probably doesn't go all the wa
It's hard to find Penetrox where I live. Are Oxguard, and NoAlox equivalent for assembling yagis etc? Anyone have a favorite? Tks , Gerry _______________________________________________ _____________
They no longer make the Fulton K1000 winch. Ids there a direct replacement so it would fit my tilt over tower fixture with no new drilling etc. I'm guessing it was replaced with a similiar model? Tks
Is anyone using a Hexbeam, either K4KIO, DXengineering or Traffie? Was wondering how they hold up in the wind and weather. I can't put my beam up too high and was thinking about one. My tribander has
I'd like to replace mt Fulton Winch. It is a K1000 which is now a K1051 I believe. I'd like to use a K1500. I hoping the holes will line up but can't find a diagram on either one. It is for a tilt ov
I need to strip off some cold spray galvanizing compound from the bolts at my tower base. I had applied the stuff as preventive maintenance over the years. I'm going to remove that tower and replace
Under separate e mail I've sent you a TT45 manual copy. 73, Gerry _______________________________________________ _______________________________________________ TowerTalk mailing list TowerTalk@cont
If I recall Tristao took over for awhile, then US Tower. I think US Tower does not consider themselves connected in any way with Wilson. The MA40 Has a square center section, not round. Much better,
The storm hit me a bit hard. I have an MA40 tilt over with rotor at base. My yagi is slowly moving around, but the tower is not. I am guessing the mast is moving inside the the inner tube. The bolts
A friend of mine does tower work and recently took down some towers and beams for the estate of a silent key. He is often on the road and asked me to post this for him since he does not get to his e