Mail Archive Search: <+subject:/^(?:^\s*(re|sv|fwd|fw)[\[\]\d]*[:>-]+\s*)*\[TowerTalk\]\s+Cutting\s+Large\s+Holes\s+in\s+Aluminum\s*$/>

Results:

References: [ +subject:/^(?:^\s*(re|sv|fwd|fw)[\[\]\d]*[:>-]+\s*)*\[TowerTalk\]\s+Cutting\s+Large\s+Holes\s+in\s+Aluminum\s*$/: 6 ]

Total 6 documents matching your query.

1. [TowerTalk] Cutting Large Holes in Aluminum (score: 1): Author: w9re@worldnet.att.net (Mike Wetzel); Date: Tue, 26 Jun 2001 01:25:27 -0500; I have aluminum rectangular blocks (4"x4"x1") that I need to cut a 3" diameter hole in (using them instead of muffler clamps). I tried a bi-metal hole saw and also a circle cutter with not much succe; /archives//html/Towertalk/2001-06/msg00555.html (8,204 bytes)
2. [TowerTalk] Cutting Large Holes in Aluminum (score: 1): Author: billwall@bellsouth.net (bill wall); Date: Tue, 26 Jun 2001 04:45:17 -0400; Hi Mike; Find a machine shop with a Bridgeport type milling machine. Most have a boring bar attachment. To save money bolt the two bars together and pilot drill your hole as large as you can. This wi; /archives//html/Towertalk/2001-06/msg00556.html (9,826 bytes)
3. [TowerTalk] Cutting Large Holes in Aluminum (score: 1): Author: kb7ww@uswest.net (KB7WW Art Moe); Date: Tue, 26 Jun 2001 05:39:11 -0700; Mike, You don't say what size your lathe is, so I will take a stab at it. Guessing you have a 10 inch I would start by putting on the 4 jaw chuck, centering the work then drill the largest hole that; /archives//html/Towertalk/2001-06/msg00557.html (10,142 bytes)
4. [TowerTalk] Cutting Large Holes in Aluminum (score: 1): Author: n9iww2@verizon.net (Kevin Adam, Webz By design); Date: Tue, 26 Jun 2001 10:05:36 -0500; You Got a Lathe and you haven't bored it out yet via drill bit and boring bar That?s the way to go bore large hole in so you can start the boring bar then just bore it out. N9IWW Kevin Adam 1239 W. T; /archives//html/Towertalk/2001-06/msg00558.html (9,609 bytes)
5. [TowerTalk] Cutting Large Holes in Aluminum (score: 1): Author: K7GCO@aol.com (K7GCO@aol.com); Date: Tue, 26 Jun 2001 17:36:38 EDT; In a message dated 6/25/01 11:26:26 PM Pacific Daylight Time, writes: << I have aluminum rectangular blocks (4"x4"x1") that I need to cut a 3" diameter hole in (using them instead of muffler clamps).; /archives//html/Towertalk/2001-06/msg00568.html (13,245 bytes)
6. [TowerTalk] Cutting Large Holes in Aluminum (score: 1): Author: davidw@copper.net (David J. Windisch); Date: Wed, 27 Jun 2001 06:17:23 -0400; I have cut 2-1/2" holes in the same stuf for the same reasons using the good (expensive) coring hole-saws in a floor-model drill press. Cut from both sides. Used lotsa cutting oil, and had no problem; /archives//html/Towertalk/2001-06/msg00584.html (7,911 bytes)

Current List: 1 - 6
Page: [1]