Mail Archive Search: <+subject:/^(?:^\s*(re|sv|fwd|fw)[\[\]\d]*[:>-]+\s*)*\[TowerTalk\]\s+Cutting\s+tubing\s*$/>

Results:

References: [ +subject:/^(?:^\s*(re|sv|fwd|fw)[\[\]\d]*[:>-]+\s*)*\[TowerTalk\]\s+Cutting\s+tubing\s*$/: 7 ]

Total 7 documents matching your query.

1. [TowerTalk] Cutting tubing (score: 1): Author: N7KA@comcast.net; Date: Fri, 28 Dec 2007 19:38:46 +0000; I have very good luck with any large tubing of any kind and getting a square cut. Just wrap a piece of paper (I use printer paper) around the tubing and align the edges that overlap. I then tape the; /archives//html/Towertalk/2007-12/msg00402.html (6,735 bytes)
2. Re: [TowerTalk] Cutting tubing (score: 1): Author: Terry <terry@kk6t.com>; Date: Fri, 28 Dec 2007 11:58:57 -0800; Another trick for cutting aluminum with a circular blade is to reverse the blade. If you don't have a lot of aluminum to cut or the correct blade is unavailable just turn the circular blade over so t; /archives//html/Towertalk/2007-12/msg00403.html (8,322 bytes)
3. Re: [TowerTalk] Cutting tubing (score: 1): Author: "Richard (Rick) Karlquist" <richard@karlquist.com>; Date: Fri, 28 Dec 2007 12:28:11 -0800; This paper technique is also useful if you have to drill two holes at 180 degrees apart. Simply mark two lines on the paper spaced apart by pi/2 times the diameter. For a 2 inch mast, this would be 1; /archives//html/Towertalk/2007-12/msg00404.html (8,262 bytes)
4. Re: [TowerTalk] Cutting tubing (score: 1): Author: Jim Lux <jimlux@earthlink.net>; Date: Fri, 28 Dec 2007 12:35:38 -0800 (GMT-08:00); --Original Message-- An even easier scheme that doesn't require calculation or measurement... Since it's hard to accurately measure (and make marks on paper) to thousandths of an inch, and it require; /archives//html/Towertalk/2007-12/msg00405.html (8,819 bytes)
5. [TowerTalk] Cutting tubing (score: 1): Author: "N2TK, Tony" <tony.kaz@verizon.net>; Date: Sun, 08 Aug 2010 18:32:28 -0400; I needed to cut off a piece of 2? x ½? walled 4130 tubing. Tried a Sawzall with a diamond encrusted blade with cutting fluid. That was pretty much useless. Made only a small cut after several minutes; /archives//html/Towertalk/2010-08/msg00188.html (6,774 bytes)
6. Re: [TowerTalk] Cutting tubing (score: 1): Author: Charlie Gallo <Charlie@TheGallos.com>; Date: Mon, 9 Aug 2010 10:03:51 -0400; Diamond is the WRONG material for cutting ferrous metals - if the blade gets at all hot (and it will), the diamond can actually dissolve into the steel, raising it's carbon content, making both the s; /archives//html/Towertalk/2010-08/msg00196.html (7,778 bytes)
7. Re: [TowerTalk] Cutting tubing (score: 1): Author: Charlie Gallo <Charlie@TheGallos.com>; Date: Mon, 9 Aug 2010 13:36:02 -0400; What tool are you using to drive the saw? The issue with ANY "grit blade" is that the "tooth" of the blade is fairly fine, so it's going to actually tend to both clog, and cut fairly slowly, BUT the; /archives//html/Towertalk/2010-08/msg00202.html (8,661 bytes)

Current List: 1 - 7
Page: [1]