The CX531N is brand new.. bill CX531N coax relay 12v, common port type N. N.O. and N.C. ports hard wired for RG58 or RG142 size coax.. will handle a couple 100 watts up to 432. heck,.. here's a data
CX531N is sold b The CX531N is brand new.. bill CX531N coax relay 12v, common port type N. N.O. and N.C. ports hard wired for RG58 or RG142 size coax.. will handle a couple 100 watts up to 432. heck,
CX600M is sold all the past stuff is sold, including the beam, but I keep finding more.. Tohtsu CX-600M coax relay.. in *like new* condition (that means it was in the rover station switching a few wa
Hi Dana and all, I meant to comment on this last year.. hah hah.. The Henry dual band tank circuit was pretty unique. The tubes ran in parallel on 6M and push pull on 2.. Not hard to believe there we
Hi Gang, I have a DEMI 902-144 for sale. It's set up for split IF and split RF though that is easily changed. It's a "902" version which means 903 is at 145 actually 903.100MHz = 145.103MHz. Set up f
all items sold thanks all!! bill Hi Gang, I have a DEMI 902-144 for sale. It's set up for split IF and split RF though that is easily changed. It's a "902" version which means 903 is at 145 actually
Hi gang, Still cleaning up. Here's something I don't need any more. It's an transverter interconnect cable for a Kenwood TS430S. I would probably fit a a couple other kenwood rigs of that vintage but
cable is sold!! (once again not asking enough I guess - hi hi!) bill Hi gang, Still cleaning up. Here's something I don't need any more. It's an transverter interconnect cable for a Kenwood TS430S. I
a couple things, first of all FT-8 does tune a few kHz so not sure a crystal controlled rig is the answer (I realize Herb was just joking,.. hah).. 2nd I agree that we are dangerously close to being
Hi all, I have here two DEMI low power transverters for sale. 5760-144LP S.N. 184 10368-144 S.N. 168 (not labeled as such but also an "LP" model.) both are working, set up for common I.F. (BNC), have
10 gig transverter is SOLD.. Hi all, I have here two DEMI low power transverters for sale. 5760-144LP S.N. 184 10368-144 S.N. 168 (not labeled as such but also an "LP" model.) both are working, set u
and now 5760 is sold as well bill 10 gig transverter is SOLD.. Hi all, I have here two DEMI low power transverters for sale. 5760-144LP S.N. 184 10368-144 S.N. 168 (not labeled as such but also an "L
I use an FT817 with my 222 transverter.. The pin goes to ground and works fine connected to the PTT jack of my DEMI transverter.. bill, k1DY According to the FT817 manual, the ACC connector has a pin
Hi all, This might be a good time to bring up "height above average terrain" for a 6 meter beam. I'll digress here a little then will get back to the point. I used to rove with the lower 6 bands. Ant
Hi all, Selling for K3IPM. Brand new unused 903 mast-mountable (RF switched) low noise preamp model SP-33. This preamp will handle 10 watts if RF sensed but 100 watts hard keyed with a sequencer. NF
Hi all, This amp was in my rover station which is being "reworked". It's a Teletec V175 that originally belonged to K1CA. It got "wet" and I replaced the whole PCB and finals (pair MRF 247's) with br
whew that was fast Amp is sold.. thanks all that *thought* about it .. bill Hi all, This amp was in my rover station which is being "reworked". It's a Teletec V175 that originally belonged to K1CA. I
Hi all, I have a DEMI 1296 transverter for sale. It came to me from Chuck, WA3IAC. This is the helical resonator filter model with a single board and the LO under a little tin can. It's in the extrud
transverter is sold, still have the amp bill, K1DY Hi all, I have a DEMI 1296 transverter for sale. It came to me from Chuck, WA3IAC. This is the helical resonator filter model with a single board an
Hi all, Worked the first hour and a half of the 2M sprint last night. Conditions were up and down but definitely seemed above normal. Best DX was KA1ZE/3, in FN01 at 488 mi. Stan peaked S-5 at one po