Here's a 4-port PCI board that I use with XP SP2 (WL, N1MM) and DOS (TRLog). It does irq sharing, so only one irq is required for all four ports. $31, including 3-day shipping. http://www.newegg.com/
-- You can do rig control and cw keying from one serial port. I use a Belkin F5U103. This unit is one of the few that can also do FSK keying, if you get into RTTY in the future. They are available on
-- I'm not familiar with the LABEL field, but the usual way to make large changes in an adif is to use the global search and replace feature in a word processor. For example, open the adif file with
-- It doesn't have to be a big deal. Go to EBay and buy a new Belkin F5U103 USB to Serial converter for $10. This will take care of rig control and cw keying. If you want to do rtty with afsk, you ju
-- I guess ignorance is bliss then, because my F5U103 works fb! I searched the archives for CW USB SERIAL, and nothing turned up. Dave Hachadorian, K6LL Yuma, AZ _____________________________________
I don't know what a microkeyer is. I don't have anything like that. You need only one soundcard. Wire up a stereo 1/8" plug for sound card "line in." left radio goes to tip, right radio goes to ring.
While we are on the subject of Bandmap enhancements, I would like the option of eliminating unworkable stations (dupes) from the bandmap. When spots are coming in from Telnet like a fire hose, the ba
You do have a STEREO plug on the Heil microphone, right? Dave Hachadorian, K6LL Yuma, AZ _______________________________________________ WriteLog mailing list WriteLog@contesting.com http://lists.con
Sound card microphone inputs require a stereo plug, even though computer microphones are all mono. Mic audio goes on the tip, shield goes on the shell. The ring is used to provide DC power to electre
You are correct. Mic audio should go to the active radio. Right-click the speaker icon in the system tray. Left-click "open volume control." You should be able to see the balance slider on the master
Try K2QMF's procedure: 1 - Open the Direct I/O control panel. 2 - In the I/O Ports Tab enter the BEGIN and END address. For LPT1 it is 378 and 37A. 3 - Click ADD button ( This is the step they left o
Do your rigs support PTT via rs-232 command? If so, maybe you can just "T" the cw keying line to both rigs, turn off the two vox's, and control which one actually transmits by the serial ptt command.
Search Ebay for Belkin F5U103. $10.98, including shipping. Dave Hachadorian, K6LL Yuma, AZ . _______________________________________________ WriteLog mailing list WriteLog@contesting.com http://lists
For USB or PCI, don't forget that you need a 20dB mic boost option if you are going to use a Heil (or any other dynamic) mic on SSB. Dave Hachadorian, K6LL Yuma, AZ . ________________________________
Maybe you can use windows/start/programs/accessories/systemtools/systemrestore to put your computer back to a time when DirectIO was working. Dave Hachadorian, K6LL Yuma, AZ . _______________________
I'm trying to get set up for the rtty roundup with so2r rtty. For the first time, I am trying to use the A/B relay for some special antenna switching, but when I transmit rtty on rig a, the A/B relay
I'm trying to get set up for the rtty roundup with so2r rtty. For the first time, I am trying to use the A/B relay for some special antenna switching, but when I transmit rtty on rig A, the A/B relay
Clive, Look at the Directio control panel and see if you have an irq selected under the irq tab. I've been fiddling with directio also, without much luck, and I saw the behavior you described one tim