There is no such thing as a CW subband. Jerry W4UK _______________________________________________ WriteLog mailing list WriteLog@contesting.com http://lists.contesting.com/mailman/listinfo/writelog
It works FB here, Bill. WL V 10.61e and IC-756PRO3. I can tune the radio from the Mouse wheel and there is no difference after entering a call into the call field. Jerry W4UK ________________________
Just this past weekend I bought two Sceptre 20.1 inch 1680 x 1050 LCD monitors from my local OfficeMax for $169 each. Good monitor, good value, adequate screen pixels and size to give a good display.
One possibility- use separate (networked) computers. Jerry W4UK _______________________________________________ WriteLog mailing list WriteLog@contesting.com http://lists.contesting.com/mailman/listi
My local Walmart has a stock of desktop PCs for $299. 8-10 eMachines on the shelf with Sempron processors and XP Home and one Compaq with a dual core AMD and Vista - all same price. 1Gb RAM, IIRC - 1
I recently practiced chip removal using a Harbor Freight hot air gun (around $10) on a few old circuit boards. I actually salvaged several parts. You might be able to remove your chip with this HF gu
See if you can reboot without the virus program running. If it is in the startup directory, move it to the screen so you have to start it manually, then reboot. Perhaps for the duration of the contes
Are you sure you used the special MMTTY plug-in engine from the WL site? Regular MMTTY won't work. Jerry W4UK _______________________________________________ WriteLog mailing list WriteLog@contesting
Not sure I understand what the "switching" problem is, but I suspect that if each radio had its own computer it might work better for you. Lots of guys run multiple networked computers. There are min
The CQ'ing stations probably could not hear each other because of propagation conditions. You just happened to be located where you could hear both. Stuff like this happens! If I am running and hear
Yes - I have it working here. I expected problems, but found when I just used the "Auto" option with Kenwood it immediately linked up with LP-Bridge and all appears well. I am having other problems,
If you specify radio type as Elecraft K2, it works OK. Apparently the K3 uses the K2 command set as a base. Jerry W4UK _______________________________________________ WriteLog mailing list WriteLog@c
If you haven't installed the "plug-in" for mmtty (from the WL "third-party" download page, http://www.writelog.com/ThirdPartyDownloads.htm ), do that and try again. Also see AA5AU's mmtty setup tutor
I am trying to get my new K1EL WKUSB working with V10.61E Writelog. I had serial port 3 unused, so set the WKUSB to use that, and then set WL to key on comm 3 with Winkey specified as the key type. N
Thanks to all who helped, both privately and here. My Commslot commands work OK. Someone mentioned using a "winkey 2" selection in setup - I only have a winkey type available. You guys that have it w
An aside: I installed it within N1MM and all is OK, so all my software interconnects appear OK. I hate to have to learn another program interface, though, and would much prefer to get it working with
Thanks, Hank. My keyer is the newest version of the USB version - only two weeks old. I will email Wayne to verify that the newer versions work with the new WKUSB. If so, I will just upgrade my WL. T
I have my WKUSB working with Writelog now. It was working all along, but mute. For those running up against this problem in the future reading the archives: When WL establishes contact with the K1EL
No problems here with 10.68f. Two networked computers. Never noticed any problem of any kind for 360 Q's. Calls highlighted AOK, etc. Jerry W4UK _______________________________________________ WriteL
V 10.68 works for me. Don't remember baud rates, etc, but I had no problem setting it up. Jerry W4UK _______________________________________________ WriteLog mailing list WriteLog@contesting.com http