Playing around in WPX, using Writelog on SSB for the first time. I made a recording on the fly for the CQ message, but it has about a 1 second blank space at the front end. When I play the message, i
I remember that. Excellent detective work by some sharp reflectorites. You got lucky on that one. I suspect you were supposed to hook up the sound card speaker output to the phone patch input on your
One more thing. If you are going to use a Heil mic, or probably any other dynamic mic, make sure your sound card has a "mic boost" option, and enable it. This option is usually under advanced recordi
Hello, Last week I was on a little DX-pedition in Gibraltar. After 2 days I got RFI problems with my laptop, the CW was not working fine anymore. So I tried to use a lot of ferrite coils, but no resu
I made two little checklists for setting up my Windows XP computer sound cards for SSB and RTTY before each contest. Maybe some of you will find them of value as a basis for your own procedures. SSB:
I don't think so. Go to mmtty/options/setup/misc, and try different choices for the "device" selection until you hit the right one for your second sound card. It's usually 1, 0, or -1. Since you are
I spent about 3 hours last night trying to get Userport to work. Writelog doesn't see ANY lpt ports in my case. All I need is the A/B signal to route com port cw keying and paddle to the active radio
The TS-850 does it, so probably all of the Kenwoods do. Dave Hachadorian, K6LL Yuma, AZ _______________________________________________ WriteLog mailing list WriteLog@contesting.com http://lists.cont
A couple of things to check: Does the Heil plug conform to the standard sound card jack? Audio on tip, electret voltage (if required) on ring, shield on shell. The plug must be a stereo plug, not a m
What? W7ZR getting into SO2R? The church is going to fall down! I got similar ominous-sounding results from Soundboardcheck on a SoundBlaster 24, but it works fb, with Heil mic to mic in, left channe
Try this method from k2qmf. It worked for me. Dave Hachadorian, K6LL Yuma, AZ -- Hello All, I have spent many hours trying to get Direct I/O to work on my new computer so that I could send CW via my
I use 3 different callsigns with my version of WL. The installation license is K6LL. When I use one of the other calls (e.g. KZ7X), I just change the message memories to show the correct call. On RTT
I don't use INSERT and PLUS for S&P. I use F9 and F10: F9 = DE K6LL F10 = R 599 AZ%L Dave Hachadorian, K6LL Yuma, AZ . _______________________________________________ WriteLog mailing list WriteLog@c
Is there an easy way to delete a station from the bandmap? I see where you can right-click in there and select menu item "remove selected entry", but isn't there a faster way, like the delete key or
-- Thanks for the suggestion, Don. I tried it, but it doesn't work here reliably. Sometimes it works, and sometimes it doesn't. The only reliable way I can find to delete stations from the bandmap is
Is there a way to have the bandmap not show dupes? It gets pretty cluttered after a while, and for certain contests I would rather not have the dupes on there. Dave Hachadorian, K6LL Yuma, AZ _______
-- Make sure you have checked WL/tools/sound board/echo microphone Dave Hachadorian, K6LL Yuma, AZ _______________________________________________ WriteLog mailing list WriteLog@contesting.com http:/
-- You click on a call in the bandmap, the receiver goes to that frequency, and you don't hear anything. It may have been a bad spot, it may be stale, the station may not have propagation to me, ther
-- BEFORE you start the application, Right-click the speaker icon in the lower right toolbar, adjust audio properties/audio select the desired sound card as the default device for recording and playb
Put %L at the end of the message. In your example, the TU key, that is handled automatically if you use the + key to send TU. Dave Hachadorian, K6LL Yuma, AZ . _______________________________________