Eric, There is nothing that you can reconfigure in either microKEYER or microHAM Router. You need to make microHAM CODEC the "default" audio recording device in the Windows Audio Control Panel. That
Bob, Have you looked at the example setup for WriteLog and your particular microKEYER (MK or MKII)? Make sure you have selected the same port for FSK in RTTYrite's Ports menu and in microHAM Router.
Bob, Sound Loopback would not have been an issue. "USB Option C" is required with nearly any USB based hardware due to the nature of the USB drivers that now set between the application and the UART.
See the WriteLog Help file under [Ports] ... you are looking for the information on "CommSlot#=N" where # is 1 - 4 the four available rig/CW "slots." 73, ... Joe, W4TV _______________________________
The thing to remember about DXDoubler or any other "SO2R controller" is that they are designed to switch the user input/output between two transceivers. With WriteLog (and N1MM Logger) already handl
Which version of Rigblaster do you have? Are you also using the RigBlaster for CW and (all mode) PTT? What port are you using for transceiver control (CAT) and what port are you using for FSK? Are y
You don't. It's hard coded. That's because MMTTY (not the plug-in) can not write userpara.ini in the directory in which MMTTY is installed. That is specified in writelog.ini (specified when you firs
CW decoding is not available in MMTTY. Select one of the "Soundboard" TU Type options. 73, ... Joe, W4TV _______________________________________________ WriteLog mailing list WriteLog@contesting.com
"Carrier" is no a symptom of a problem with userpara.ini. It is an indication that there is a mismatch between the transceiver mode and the MMTTY configuration. MMTTY and most transceivers can opera
Radio | This Window is ... and uncheck the left or right designation. 73, ... Joe, W4TV _______________________________________________ WriteLog mailing list WriteLog@contesting.com http://lists.con
The error message means that MMTTY can not write the Userpara.ini file. You will need to determine if the file does not exist (it needs to be read before it can be written), whether the file is mark
No. There is no FSK input via the USB port. You can use it for both control (CAT) and audio (USB sound card) but you will still need another USB to serial converter or traditional serial port to gen
Update! 10.71C is two years old there have been several significant improvement in that period of time. 73, ... Joe, W4TV _______________________________________________ WriteLog mailing list WriteL
The solution may be to change the command from RT0; to RU0000; as that will set the RIT to 0.000 KHz offset or to RD0000; which will set RIT to -0.000 KHz offset. You may want to try the FT-950 driv
Not only is there no RIT clear command in the Icom firmware - there is no provision to either read or set the RIT/XIT frequency or RIT/XIT status. Of course, the 7600 firmware contains such importan
See the [Rigs] section of Writelog.ini description in WriteLog's help file. 73, ... Joe, W4TV _______________________________________________ WriteLog mailing list WriteLog@contesting.com http://list
In the RTTYrite menu - select TU Type | TNC Setup and *uncheck* the box that says "RTTY Control is always on top" 73, ... Joe, W4TV _______________________________________________ WriteLog mailing li
Disable PTT on the CW port or from WinKey 2. In the Omni VII, PTT acts like a straight key (see "external CW Input Plus CW Keyer operation from paddles" on page 33 of the Omni VII manual. In general
It's possible if some programmer wants to take on the effort. You don't have to set up the 706mkIIg as a 706. See "Writelog.ini [RIGS]" in the Writelog help file ... pay attention to information on
The "All mode PTT on RTS" setting works just fine as does "Comm PTT" if your transceiver supports PTT via CAT command (not all do). In general if your interface includes a Winkey device for CW, sett