I had the same problem and the final solution was to open up the computer and look at the serial connection. The board was not pushed all the way in so it wasnt making connection..Once that done and
I was having the following problems with WL. Since I run SO2R I was having problems with 1. Direct I/O. I purchased it but about 3 weeks ago or so a pop up was telling me my evaluation version was ru
I have finally gotten Writelog to work with SO2R Dx doubler..My computer has 2 usb ports that I donot use and 3 serial ports and a LPT1 port and a printer port. I want to use N1MM on Rtty or some con
I have one computer that was built for me and has plenty of memory and serial ports and two LPT ports. I am currently using 10.60 with SO2R using Writelog and DxDoubler box etc. rigs are Ft1000D and
This morning early I looked for wrtielog ini file. I seem to have a couple in the computer. How do you tell which is the correct one. I dropped the old contest for all ini and still they show up when
I want to set up my SO2R station for RtTY using 2 Rig blaster plus..How do I do this???? email ukbrown@aol.com or ukbrown@acsol.net thanks bill UK PTL _______________________________________________
A different slant...how do you get WL 10.61 to send cut numbers. I use %1 which uses no cut number or zeros or %3 which uses Zeros....any idea what to put in the ini file..I know I have it there unde
How about a module for the Colorado QSO Party..thanks PTL bill K0UK -- Original Message Follows -- From: writelog-request@contesting.com To: writelog@contesting.com Subject: WriteLog Digest, Vol 52,
I bought a used IC706 Mk 11 and need to know what I need to hook it to a lap top. thanks PTL bill K0UK _______________________________________________ WriteLog mailing list WriteLog@contesting.com ht
As usual I wait until the last minute on this...I need info on how to get the IC706 to work with a lap top running Writelog. I bought the cables from K1NU for cw and computer control. I have two old
Just read about some one using %Z x1 what is its function???thanks PTL bill K0UK _______________________________________________ WriteLog mailing list WriteLog@contesting.com http://lists.contesting.
Has anyone running Writelog or any other contesting program got the IC706 too interface with the program for freq read out and cw. Especially using K1NU cables. Please if you were able to make it wor
This has been a bad expersience for me with the above set up. I have tried all combinations and I still cant get the freq to read out properly nor for it to send cw properly. Not sure if its in the i
I have a Compaq E500 laptop with Write log latest version on it. But the clock in the laptop doesnt seem to communicate with Writelog. I did the Cal. Qso Party and I had to manually put in the times.
I have version 10.68F..havent upgraded yet. In the above contest it didnt show RW0CWA, P40TA nor ZF2AH as DX mult. Plus it missed 1 of my sections. Has anyone else had this problem and how do you sol
I just recently had to send my FT1000MP to have some repair work to it. I swapped in a FT1000D into my SO2R station. But everytime I set up a new contest I have to go to ports and set it up as the FT
Can anyone tell me how to set up Writelog for SO2R cw contest so that the program automatically starts sending cq on the other radio as I am typing in the report from the other..Havent figured out ho
I need the code for Direct IO for the IC 706 Mark 2 G to get the Direct program to work on cw..Let me know via ukbrown@aol.com Please..thanks I will be out of town till Oct 28th...PTL bill brown ____
I have the latest version 11.17E completed the 10mtrs test and went to set up Cabrillo and got the message to setup parameters first. Clicked OK and nothing happened. Save the contest and reopened an
Went to the parameter setup but its greyed out. bill brown K0UK _______________________________________________ WriteLog mailing list WriteLog@contesting.com http://lists.contesting.com/mailman/listi