It works fine with WL. Just enter 127.0.0.1 and port 7300 as your telnet node in WL. 73, barry W2UP -- Barry Kutner, W2UP Internet: w2up@mindspring.com Newtown, PA Frankford Radio Club ______________
Don't forget to add the cost of a 2N2222 and a 1K resistor. That would add at least 25 cents to the cost of the most sensible solution. Barry W2UP -- Barry Kutner, W2UP Internet: w2up@mindspring.com
In my experience, a space is needed before and after the < and >. Don't forget, a single < will only increment the speed by a few WPM and may not be noticeable. Try using 4 or 5 of them. 73, Barry W2
Is there any way to have the Packet Spot window default upon opening with the In-band and Mults only boxes checked? Tnx, Barry-- Barry Kutner, W2UP Internet: w2up@mindspring.com Newtown, PA Frankford
A word of advice: If you are going to be operating the ARRL SSB contest (SSB - yuck), wait until AFTER the contest to do the upgrade... 73, Barry W2UP -- Barry Kutner, W2UP Internet: w2up@mindspring.
I'm pressing Shift-Fkey to record on the fly, but it's not working. Just replays the existing message when I hit the Fkey. I have the Wavefiles directory set in the Wavefiles Locate button in the Por
While installing the latest upgrde, got the following error box: Compnent Move Data had Fatal Error Media Name: MEDIA Error # -132 Ideas? Tnx, Barry-- Barry Kutner, W2UP Internet: w2up@mindspring.com
OK, first... My recent install of 10.53 with the error. I just turned off the computer, rebooted, reinstalled the upgrade and all went fine. Next... The record on the fly problem, I brought up on Fri
It would have been even nicer if you checked the reflector archives for the email YOU somehow MISSED, before getting all nasty in public. Barry W2UP -- Barry Kutner, W2UP Internet: w2up@mindspring.co
Same happened to me. I just tried the install a second time and it worked. 73, Barry W2UP -- Barry Kutner, W2UP Internet: w2up@mindspring.com Newtown, PA Frankford Radio Club ________________________
I do it all the time. It's second nature now. Suppose DL1XYZ answers my CQ. After I type the X, I hit INS, then continue typing the call. It allows me to save maybe 200 msec in responding. Even bette
Your suggestion is not a good one. For maximum efficiency, one should hit ENTER part way thru the call, so you come back to the other station sooner, and complete the typing of the call as it is bein
Was setting up for WAE yesterday. 2 computers networked, one XP Home, other 98, same setup I've used for about 4 years. WL 10.53E After clicking Link to Network, an error box popped up on the other c
Trent, I'm not aware of the resistor mod. The pre-V6 firmware caused the radio to lock up for 6 seconds while it talked to the computer. Apparently, it downloads the complete parameter set when any c
I use it, no problem. I just enter the "local" computer IP address. I don't recall it offhand, as I'm not at home now, but it's the same address and port number I use in DX4WIN. Barry, W2UP -- Barry
Hi all, I'm setting up for CQWW CW and on my second computer, it seems that I can't run the CW decoder window and record audio at the same time. It works fine on computer 1. A little window pops up "
A few other options to minimize Band Map clutter: 1. Adjust the bandmap spacing using the PixelsPerKhz parameter in writelog.ini 2. Lower the DefaultTimeoutSeconds so spots auto-erase more quickly. A
Did a little playing around today, and here's what I have found: If I start CW decode, then go into Sound Board Options and Enable Recording Loop first, I get an error saying the sound card is in use
I've used Writelog for a long time and I used to be a strong supporter of Writelog. My view has changed. While it is, overall, an excellent contesting program, lots of people have lots of quirks with
I've operated WAE for many years (even before computer logging!) and the QTC issue has never been a problem. It's fairly common for stations worked early in the contest to come back and ask for QTCs