Check the "PTT" box on the FSK port (COM 7) in Router (MMTTY will operate PTT in FSK) and set PTT to COM 6 RTS WL Will operate PTT in CW and SSB. You DVK audio will need to come from a separate sound
Barry/Jon, If you have COMM PTT enabled, it is possible that the "PTT Off" command is getting clobbered by collisions on the CI-V bus. Disable COMM PTT and use RTS on the CW port (or LPT if you have
Jon, x Comm PTT YES If you are going to use "All mode PTT on CW Port RTS" the ports for CW and PTT need to be the same in Router (both COM4 or both COM 6). See: www.microHAM.com/Downloads/DK_WriteLog
Jim, With respect, the microHAM products were done correctly with regard to any "pin 1 problem." The radio interface cable is shielded with all shields connected to the shell of the DB37 (connected t
Hans, Please look at www.microHAM.com/Downloads/MK2_Writelog_Setup.pdf Using the Writelog Mixer Control (WriteLog Programs), configure WriteLog to use "microHAM CODEC" for all four of the "Radio Audi
Sorry, the server is case sensitive. The correct URL is: www.microHAM.com/Downloads/MK2_WriteLog_Setup.pdf _______________________________________________ WriteLog mailing list WriteLog@contesting.co
Hans, They don't! Writelog has its own software DVK that uses the soundcard in microKEYER II. I suggest studying the WriteLog Help file under DVK as well as reviewing the information at http://writel
The link to the message in the archives is: http://lists.contesting.com/archives//html/WriteLog/2007-09/msg00074.html a simple search for "vista and writelog.ini" 73, ... Joe, W4TV __________________
Scott, Note that Vista does not allow users to WRITE to any file in the C:\Program Files\ tree. Vista will virtualize any user file in the C:\Program Files\ tree into the "<username>\APPDATA" tree. I
Jim, To follow up on this one time ... Others may have fixed alleged problems with "microHAM products" by adding ferrite chokes on the interconnect wiring but they are masking a problem that lies els
Why don't you write the wrapper for MMVARI just as someone else did for MMTTY many years ago? MMVARI is available as an OCX and only needs the appropriate interface for WriteLog to use is as a "load
Phil, It is possible to run two programs on one sound card without any degradation under one condition. The sample rates of both programs must be the same or INTEGER multiples of each other. For exam
Pumping the AGC is ALWAYS a factor if the receiver IF bandwidth is greater than the bandwidth of the desired signal. When operating PSK31 with a 3 KHz IF bandwidth and "panoramic" (e.g. waterfall) d
Router 5.1.1 has been released. This version contains several fixes and one significant operational improvement. Those still running a version of Router prior to 5.0.0 should follow the upgrade instr
Completely inaccurate. Vista happily supports BOTH standard serial and LPT ports. My Vista test/support system has three serial ports (one on the motherboard and two on a PCI-e card) and two LPT por
Dick, Do not use "Software generated FSK." Treat MK2R+ and Router as if they were a hardware UART. Check "strict BPS" on the FSK port of Router and add two or three extra spaces at the end of the Wri
Bob, This is one of the more common symptoms of common mode RF on the various control lines - particularly if you are using "COMM PTT" (or serial commands for PTT). See the various online referenced
Dick, I can run the MMTTY plug-in on COM6 even with K1EL WinKey selected as the CW type. Make sure you have not configured something else to use COM6 in the Writelog Ports Setup dialog. 73, ... Joe,
WriteLog will not use the DVK built into microHAM Router. However, you don't want to use that DVK anyway since WriteLog's own DVK will work just fine with the soundcard in the microKEYER II. Before s
The K3 identifies as a TS-570. Either the K2 setting - or the general "Kenwood" setting (not TS-850) should work. However, since the K2 did not use handshaking (unlike Kenwood), using the K2 setting