- 1. [Yaesu] FL7000 (boat-anchor) (score: 1)
- Author: "Ross" <rbiggar@ihug.co.nz>
- Date: Thu, 5 Jan 2006 16:37:56 +1300
- I need some advice on what to do with an FL7000 amplifier, (apart from using it as a boat-anchor). It has the problem of going into protective mode at very power. I can get an output of no more than
- /archives//html/Yaesu/2006-01/msg00008.html (6,660 bytes)
- 2. Re: [Yaesu] FL7000 (boat-anchor) (score: 1)
- Author: "Ross" <rbiggar@ihug.co.nz>
- Date: Sat, 7 Jan 2006 06:56:36 +1300
- Sean, and others, Thanks for the comments, to give you some idea of the problem, transmitting into a dummy load, with the FL7000 output at only 125watts, it lasts 2minutes plus/minus 10secs before cu
- /archives//html/Yaesu/2006-01/msg00021.html (8,451 bytes)
- 3. [Yaesu] Fw: Ft1000MP and CW (score: 1)
- Author: "Ross" <rbiggar@ihug.co.nz>
- Date: Thu, 1 May 2008 16:03:06 +1200
- Hi a query for all. I have an odd problem with my FT1000MP. It works well, but when I push the CW button, I get a loud tone from the speaker, rather than the normal band noise. Can someone please exp
- /archives//html/Yaesu/2008-05/msg00000.html (6,406 bytes)
- 4. [Yaesu] Yaesu FT1000MP and CW (score: 1)
- Author: "Ross" <rbiggar@ihug.co.nz>
- Date: Thu, 1 May 2008 16:06:13 +1200
- Hi all, Can someone help me please. My Ft1000MP works well it transmits and receives on all modes except when I switch to CW the speaker gives a loud tone, instaed of the normal background static. Th
- /archives//html/Yaesu/2008-05/msg00001.html (6,877 bytes)
- 5. [Yaesu] FT1000MP and CW (score: 1)
- Author: "Ross" <rbiggar@ihug.co.nz>
- Date: Thu, 1 May 2008 16:34:42 +1200
- Dave, thanks for your advice. yes you are correct I had a key in the back panel key jack, being the key from the US Navigator interface Thanks for the help Regards Ross ZL1WN ________________________
- /archives//html/Yaesu/2008-05/msg00002.html (6,270 bytes)
- 6. [Yaesu] FT1000MP and CW---Thanks (score: 1)
- Author: "Ross" <rbiggar@ihug.co.nz>
- Date: Fri, 2 May 2008 18:11:21 +1200
- Thanks to all that commented, my face is a bit red. I am using a US Interface Navigator and I had plugged the key into the rear key jack of the FT1000. Thanks to all those who led me to finding this
- /archives//html/Yaesu/2008-05/msg00003.html (6,393 bytes)
- 7. [Yaesu] FT1000MP and Transverter output (score: 1)
- Author: "Ross" <rbiggar@ihug.co.nz>
- Date: Tue, 10 Mar 2009 17:47:35 +1300
- Hi all I have a question about the transverter output power on an FT1000MP The book says a variable low leve; approx -6dbm 100mv @50ohm ouput. What does this convert to in milliwatts, and how much sh
- /archives//html/Yaesu/2009-03/msg00003.html (6,966 bytes)
- 8. [Yaesu] Re FT1000MP and TRV output power. (score: 1)
- Author: "Ross" <rbiggar@ihug.co.nz>
- Date: Wed, 11 Mar 2009 13:40:37 +1300
- Thanks to those who replied to my question, your comments were a great help. When checking I was looking for a higher output , and as I was using a 30db attenuator it didn,t leave much for the HP438
- /archives//html/Yaesu/2009-03/msg00004.html (6,652 bytes)
- 9. [Yaesu] Increasing FT1000MP Transverter output (score: 1)
- Author: "Ross" <rbiggar@ihug.co.nz>
- Date: Tue, 17 Mar 2009 16:13:53 +1300
- Thanks to those that replied to my question about the FT1000MP transverter output. Yes I finally measured it with my power meter and it is a lot lower than I expected, from 0 to .1mw max. I would lik
- /archives//html/Yaesu/2009-03/msg00015.html (6,727 bytes)
- 10. Re: [Yaesu] Increasing FT1000MP Transverter output (score: 1)
- Author: "Ross" <rbiggar@ihug.co.nz>
- Date: Wed, 18 Mar 2009 15:30:05 +1300
- Ralph, that is how I run all my transverters, I have seperate tx and RX lines from the rigs, at 30mhz to the transverters and from them to the main relay at each of the various arrays/dish, on 144, 4
- /archives//html/Yaesu/2009-03/msg00019.html (9,719 bytes)
This search system is powered by
Namazu