Could anyone on the list tell me what the normal output of an OMNI V be? Mine has the QRP mod and with full counterclockwise of the internal ALC adjustment pot I get the following output. 10 Meters 8
I have a Corsair II and an OMNI V. When I hook up my Shure 526T Series II to the Corsair II I show peaks of 65 watts on SSB however, when I hook the same mike to the OMNI V I only show voice peaks of
I have an old Turner M+2/U handheld mike that I would like to try on my OMNI V. Has someone wired a Turner to work with a TT radio? The only specs I have on this mike is that it is relay switching an
Ed, I got it to work. Did as you told me and switched it to electronic switching. Then rewired the mike plug. However, when I went to Radio Shack to replace the battery I was told it is now a special
Talk about strings that provoke bad luck. Come on guys it is like some of you are wishing that Ten Tec went under. These post are out of control. One guy leaves for a better future and all at once it
Talk about strings that provoke bad luck. Come on guys it is like some of you are wishing that Ten Tec went under. These post are out of control. One guy leaves for a better future and all at once it
Airpax comes in three types slow, fast and instant. The slow will not work. The fast is what TT puts in. The instant will drive you to drink. I bought a fast type and use it off of my Astron to run b
Don I have a Corsair II and I have a question of you. You say on your add that your Corsair II has a nice crisp bandswitch. Did you repair it? I have a bandswitch on mine that is nice and crisp when
Jim, you think they all have movement after it goes into band? I have nothing to compare mine to. Dan N4VET _______________________________________________ TenTec mailing list TenTec@contesting.com h
I think you may be right. Ten Tec does not seem to know either. I don't know if this is normal play because I don't have another Corsair II to compare. Dan N4VET _____________________________________
Thanks Paul for your reply. No mine falls right into band. The play is in the index. You would not happen to know of a replacement part from a switch company would you? Thanks, Dan __________________
Has anyone on the list tried to modify an Omni V or a Corsair II so that an IF signal can be obtained from the radio for the hookup to the IF input of a monitor scope? Thanks, Dan N4VET _____________
I would check the power supply itself. Could be that when the power supply gets hot it cuts back on power to the rig. Also, your finals could be going south from old age. This can cause a power suppl
Jim, how did you fix the readout? Dan N4VET _______________________________________________ TenTec mailing list TenTec@contesting.com http://lists.contesting.com/mailman/listinfo/tentec
Bill, will this thing that is on the way work on an OMNI V? Or, are we out of luck? Dan N4VET _______________________________________________ TenTec mailing list TenTec@contesting.com http://lists.co
Has anyone used the Hamscope program as a spectrum scope for view of SSB signals? Does Hamscope see SSB signals on its display? I am thinking of downloading the program but only for SSB. If not usefu
I can't seem to get EHAM to load. I am told Website not found. Is it me or is it gone? I got a notification of equipment for sale yesterday from them. Dan N4VET ______________________________________
I was told that the death of BIll Fisher could be the reason for the non-loading of the sites. Could be that the reflector is next. I was told that both sites were taken care of by Bill. Kind of like
Have an Omni V need to go buy a bulb for the S Meter. My book shows it takes two. It however does not tell me the number of the lamp type. Is it the same bulb as in the Corsair II #1892? If not, does
Thanks Bill. Dan N4VET _______________________________________________ TenTec mailing list TenTec@contesting.com http://lists.contesting.com/mailman/listinfo/tentec