I am at the end of my rope. Can't seem to find an explanation for why I can only get 80 watts output on 10 and 20 meters with my OMNI V when on a Butternut HF6V-X and my Butternut Butterfly Beam but
I am thinking along the same lines and am interested in what you find out. Dan/N4VET _______________________________________________ TenTec mailing list TenTec@contesting.com http://lists.contesting.
The Display on Omni V is bright when I first turn it on but dims after a few minutes. The radio works fine but for the display. At times it turns bright again and back to dim. Seems to be no reason f
The Corsair II is the best radio that TT made. If you can't hear it with the Corsair II it is not there. Add an outboard DSP filter and an equalizer for the mike and it can't be surpassed. Have not u
Well said Dennis. I have also owned many rigs and I can tell you that Ten Tec is flat out one of the best. My Kenwoods, Icoms are gone but not my Ten Tecs. They are by far the easiest radios I have e
I can hear it in my head without a rig. It is about an S9. Am I going crazy? Am I sending out the signal? Does anyone else hear it without a rig? Am I the only one? Could this be the end of N4VET? Da
I have a Timewave DSP-9 that I have had inline with my Corsair II and has worked fine. However, when I hook it up to my OMNI V to it I can hear myself in the external speaker as I transmit. It is not
I have an Airpax 20 amp and an Airpax 18 amp fuse. Both are fast acting. I use the 20 amp on an OMNI V and have been using the 18 amp on my Corsair II. The Corsair II calls for a Ten Tec 260 power su
I have an Airpax 20 amp and an Airpax 18 amp fuse. Both are fast acting. I use the 20 amp on an OMNI V and have been using the 18 amp on my Corsair II. The Corsair II calls for a Ten Tec 260 power su
If you want an NOS D104 elements you can still get them here in Tampa at a place called Jefferson Electronics 1040 W Hillsborough Ave. Tampa, Fl. Phone 813-239-2500 He also has the microphones for sa
IMHO that auction site and others like it are causing the death of one of the most fun parts of HAM radio. As many of you know, if you have been to any Hamfest lately, they are getting smaller and sm
Hamfest were not like that and that is my point. What is left now at Hamfest is the junk one level below the junk on the auction. The auctions had a lot to do with the sorry state the Hamfest are in.
That's my point Dave. They do not attend because they buy at auction. They do not attend because they sell at auction. They do not attend and they get taken at auction. It is the fault of HAMS. Start
I want to hook up an Ameritron 811 to my OMNI V. Don't want to break anything so I better ask. My OMNI V book only shows how to hook up Ten Tec Amps. What RCA on back of OMNI V goes to key the Amerit
Good work and good luck. _______________________________________________ TenTec mailing list TenTec@contesting.com http://lists.contesting.com/mailman/listinfo/tentec
I hooked up an Ameritron AL811 to my OMNI V. I get full output on all bands but on 10 meters when I put OMNI V meter to reflected power it shows an SWR of almost 3 to 1. SWR creeps up the meter slowl
I bought an Ameritron AL811 Amp and hooked it up to my OMNI V. On 10 meters the OMNI V meter on reflected power reads a little under 3 to 1 when I tune the amp using either the tune or a pulser. My a
Seems the meter on the OMNI V may be the problem. Did more investigating since last post. High input SWR on reflected setting of OMNI V meter only takes place when I use CW mode and pulser to tune Am
Malcolm, I feel the same way. My Corsair II is very stable as is. Once it warms up I get very little drift. Dan/N4VET _______________________________________________ TenTec mailing list TenTec@contes