Andrew Moore 16 George Street Kittery, ME 03904 Personal check is fine. Will ship to: Thanks, --Andrew _______________________________________________ TenTec mailing list TenTec@contesting.com http:/
Winston - I received the payment for the digital dial today - haven't boxed it up yet but will do so tonight and it should go out Friday. Thanks, --Andrew ____________________________________________
I read that the Corsair 1 (model 560) and Corsair II (model 561) remote VFOs (models 263 and 263G, respectively) are identical except for their color (http://home.comcast.net/~w8kc/tentec.html) Can s
Turns out it was the metal sockets on the accessory jack. A previous owner had jumpered two of them with a wire so thick it increased the diameter of the sockets, so that when the remote VFO's acces
Model 560 (Corsair 1) with manual $350 plus shipping. Second owner Works perfectly, looks excellent. Photos available. _______________________________________________ TenTec mailing list TenTec@conte
Sorry to spam the lists with this but I figure there are lots of CW ops here who might have what I'm looking for. I picked up a set of V2L paddles (by Stan, W9WBL) but they didn't include the page th
Thanks Lyle - yeah, I remember there were three pages that came with mine: the brochure showing the various models; the 'instruction sheet'; and a sheet showing the physics & forces behind the desig
Sorry list - didn't mean to copy you all... ... _______________________________________________ TenTec mailing list TenTec@contesting.com http://lists.contesting.com/mailman/listinfo/tentec
I have a pair of Ten-Tec model 263 VFOs that I no longer need. These are the dark color to match the Corsair I. However, the 263 still works on the Corsair II. The 263 and 263G are the same except fo
Idiom Press CMOS4 keyer. I bought it new a few months ago, assembled it and then sold the rig (Corsair I) that I was going to use it with. It's barely used, perfect condition. High quality build (I h
Model 282 (250 Hz) Model 285 (500 Hz) Model 288 (1.8 kHz) $65 each plus a couple bucks to ship. _______________________________________________ TenTec mailing list TenTec@contesting.com http://lists.
The pair of Ten-Tec 263 VFOs I posted earlier have been sold. --Andrew _______________________________________________ TenTec mailing list TenTec@contesting.com http://lists.contesting.com/mailman/li
The CMOS4 keyer that I posted earlier has been claimed. --Andrew _______________________________________________ TenTec mailing list TenTec@contesting.com http://lists.contesting.com/mailman/listinfo
Posting to these three lists in hopes that a homebrewer / tinkerer type might be interested. I have two of the following Hammond heavy duty, 19-inch desktop racks, each 6U height, never used. Couple
I'm interested in putting a Ten-Tec model # 937 power supply into another enclosure. Would someone mind emailing me dimensions of the 937, and if possible, a snapshot of the inside? _________________
Not sure if this is normal or not... but when I switch the meter on my Corsair II to the "Ic" position and put the rig into Lock mode, the needle jumps around a lot and never settles. It never stays
<< If I'm not mistaken you said the meter is steady in the Power Out and SWR positions. That being the case, I'd suspect a dirty contact on the meter switch. Why not clean them and see? Easy enough.
Can't remember the exact display freq but it almost sounds like 9000 is the frequency displayed when there's no VFO signal. This happens when you reverse the remote VFO in/out wires or when the remov
Omni VI / VI+ / etc... I've owned two in the past, loved them, but found the audio (CW) fatiguing to listen to. Kept wanting to change the pitch or tweak the VFO or filters to reduce the fatigue. End
I don't think so -- I noticed it with both. I'm not sure how much DSP or noise reduction happens in the VI+, or the quietness of the receiver compared to what I'm used to, but something about it jus