Not Yet. I think it's as much a matter of where to put the components as anything. With a few of the right jumpers, both control and coax, it appears that it would work Dave WA3MKB Has a scheme been
The problem of heating an unmatched balun is one of the reasons that I chose the Palstar AT5K. It has a 1:1 balun at the input side of the tuner, that way it sees a 50-ohm load on each side when the
The article was in the April 2002 issue. When on the ARRL site, you can query for article name, or author or date. Dave WA3MKB Thanks, Bob. Actually, I should have pointed out in my original post th
Original labels came from Carl, N4PY. If I were you, I'd contact him. If he has them available, I'm sure the price is fair Dave WA3MKB Hi. I have a OMNI-V with the n4py 9.2 chip... works just fine. W
You might want to check your tuning rate. It's in Menu 3 and comes up as SPD. Dave WA3MKB John it may be a PLL problem. Ron K3MIY --Original Message-- From: tentec-bounces@contesting.com [mailto:tent
Whether new or reused, all antenna connections, especially telescoped tubing need to be cleaned. The antiseize greases (I've always used NoALox or PeneTrox, but there are many others) designed for al
I have 2 Omni VI+. One is all TenTec filters, the other is all InRad. Both have the InRad 600 Hz Roofing Filter Mod operated by the N2 button. The all-TenTec filter unit has the 2017 500Hz filter in
Unfortunately, those of us with 40+ years as hams (some more, some less) see things as hams of long standing. However, a ll you've got to do is go to a small local hamfest, one that attracts the new
Palstar builds great tuners. I love my AT5K. However, I also have an original TT 238. The difference is a Pi (In the Palstar) vs an L (in the TenTec) configuration. The problem with the Pi is that it
This URL is a great place to start. The tentecwiki.org site has info on all TenTec, old and new http://www.tentecwiki.org/doku.php?id=550 Just click on the line above and you'll be taken to the Pegas
I've got a spare TenTec 285 filter for sale. It's the 500 Hz filter for the 6.3 MHz IF of the TenTec Corsair Corsair II Paragon Paragon II Omni V Omni VI Omni VI+ Great CW filter Price is $70 and tha
The filter is sold pending funds. Thanks Dave WA3MKB I've got a spare TenTec 285 filter for sale. It's the 500 Hz filter for the 6.3 MHz IF of the TenTec Corsair Corsair II Paragon Paragon II Omni V
I've got two spare TenTec filters for sale. The first is a model 285 It's the 500 Hz filter for the 6.3 MHz IF of the TenTec transceivers listed below The second is a model 282 It's the 250 Hz filter
I've got a TenTec 285 filter for sale. It's the 500 Hz filter for the 6.3 MHz IF of the TenTec transceivers listed below This filter works great in the 6.3 MHz IF of the TenTec Corsair Corsair II Par
I've got a TenTec 2017 filter for sale. This is the latest version of the 217 filter. It's the 500 Hz filter for the 9 MHz IF of the TenTec transceivers listed below This filter works great in the 9
TenTec 708 or 709 Dave WA3MKB I have a model 706 desk mic that has lost most of the out put. It still has output, but I must run the Mic Gain on the Orion 1 up to 50 to 75, and it will drive the VOX
First, the 5th supply is for control. It provides a voltage to the on-off switch of the Herc II, and that in turn turns on the 4 12-volt supplies when the Herc II is switched on. Second, there is a m
Many hams will list their rig in this reflector, on QRZ.com or qth.com with the caveat, "pickup only". Then you can demo the rig with the potential purchaser. I sold my last 2 Omni VI Opt 3's that wa
Sorry to step back to the original topic of this thread, but I just got my new issue of CQ and the TenTec 610 is pictured on page 28 (bottom right) with a note about it on page 30 (top left). Dave WA
They are allen screws I am helping a friend to change the pointer cord on his 238 tuner... having trouble finding a allen wrench to fit the screws for the inductor and capacitor knobs...are they alle