I looked back thru the achieves but didn't get much data on anyone trying N6BV published mods of the Hygain 155BA/CA . So here's the question again: Need input/experiences of any op that has re dimen
TNX Pete fer the reply. Yes if you run across the file pse pass it along. I have tried to find a copy of YO but nw no longer being produced. I have found Antenna Model by Teri software that is simila
I purchased "Cord Grips" from www.elecDirect.com a year ago. All sizes are available. Nylon body and internal sealing gromet. Used to terminate LMR-600, 400 and rotor cables in a Hoffman enclosure. V
Just installed three Tic Rings on three different towers (25G) enabling me rotate lower ant on 10,15,20. I have searched the this reflector but not much info on this. I know there are a lot of these
TNX Mike and Tim. Since I have guy wire just underneath I will use the stru method per Mike. Just got back from hardware sore with some aluminum angle to do the job. Both your responses much apprecia
Take a look at www.MDS-ham.com. I have been using these controllers in place of original on G-800 and G-1000 with great success. Gud hunting, Tim, KY5R _______________________________________________
Mike I can share some extreme experience with the HDBX-48: While residing in KP4 for many years I had two HDBX-48. It wasn't until hurricane Hugo that I experienced any problem. Both towers came down
Getting ready to receive a new M2 40M3L 40mtr yagi. Need anyone who has one in the air or owned one in the past to explain how you got adjusted to the part of the band you wanted. Instruction manual
Thanks to all for the info. I have some confidence now about setting up the 40M3L and tower adjustment. TNX again, Tim - KT4TX _______________________________________________ ________________________
Looking for a reasonably priced source of surplus or used 1 1/4 or 1 5/8 inch hardline (heliax or smooth). Need a 300 ft and 200 ft run or 500ft spool for a new VHF/UHF antenna installation. Thanks f
Looking for a manual core/prep tool for FXL-1480 1 1/4": Commscope P/N 114-HPT Also Female N conncector for FXL-1480: Commscope P/N 114EZNF Apparently the new Andrews/Commscopre company is no longer
Bill; I have been using the MDS RC-1Y on three G-1000's which has RS-232 port for the past 4yrs. Works well with N1MM rotor control. Also using a custom programmed model to control three TicGen ring
Anyone been in contact with these folks lately? I can seem to get a reply......... TNX fer any info, Tim, AB4B _______________________________________________ ________________________________________
Anyone have any insight into the difference between the Yaesu G-1000 rotor vice the G-2800 rotor mechanically? Also practical use/loading of a G-2800 ie type of antennas it will reliably handle......
Thanks to all who responded. Will proceed ahead with acquiring a G-2800. GE es gud wknd, Tim, AB4B _______________________________________________ _______________________________________________ Towe
I have come into some 3 " boom material and am looking at upgrading my 20mtr ants (2x 204BA 1/2w spaced on 80ft 25G). Anyone have any designs or practical apps on this issue? Trying to get a leg up o
I would suggest you look at the ARR P 0.5 - 30/20DV bipolar preamp. It's pretty stout and not very expensive...... www.advancedreceiver.com It's listed in the in the LF preamps section. I have been u
Bill..... You need to chat with Fred K6IJ ex KH7Y.........k6ij@volcano.net HD Tim, AB4B _______________________________________________ _______________________________________________ TowerTalk maili
Would anyone have a couple of connectors for this old discontinued coax? have acquired 350ft unused over the weekend. or Any methods to make simple connectors with hdwe store materials? TNX fer any i
Thanks all for info. Found some connectors and have all the homebrew connector info from those who replied. Now just have to wait till spring as 40 deg es cold rain all day. At least no snow today er