You might be able to ask TT about this. In years past, they would do a board swap and just send you the new board. 73, Carl Moreschi N4PY 121 Little Bell Drive Bell Mountain Hays, NC 28635 -- Origina
57600 baud 8 bit no parity 1 stop bit Carl Moreschi N4PY 121 Little Bell Drive Bell Mountain Hays, NC 28635 -- Original Message -- From: "Eugene Klingler" <n8zx@hughes.net> To: "Discussion of Ten-Tec
The Orion only runs at 57600 baud, 8 bit, no parity, 1 stop bit. Carl Moreschi N4PY 121 Little Bell Drive Bell Mountain Hays, NC 28635 -- Original Message -- From: "G3RXP" <g3rxp@btinternet.com> To:
You can cut out the louvers themselves on the air intake. This does reduce the fan noise some. I did that and also added a 100 ohm resistor in series with the fan motor to slow it down some. This wor
Here's my wild speculation: Use 9 mhz as the first IF when in the ham bands, and 45 mhz when outside the hambands. This would give you the Orion main receiver scheme inside the ham bands and the Orio
Steppir makes a Y connector. This allows both your computer and steppir to be connected to the Orion at the same time. This works because in this setup, steppir only listens on the comport and does n
I have many of my N4PY Orion users doing exactly this. They simply run a Y serial cable adapter to connect the Orion serial port to the steppir controller and computer. Then they select the option in
I have a Tennadyne T8. It has performed extremely well for 12 years. There are no traps or motors or anything to go wrong. The antenna covers 14 to 30 mhz very well with a good front to back ratio an
Look at the layout of the number pad between the 302 and the Orion. You will see on the Orion that number 1 is in the upper left. On the 302 you will see that number 1 is the lower left. So, on both
I am cleaning out the shack here and I have some items for sale. Model 217 500 hertz 9 mhz filter for the Orion and Omni's $65.00 including shipping. Model 218 250 hertz 9 mhz filter for the Orion an
Yes, it is available. You can go to www.paypal.com, select "Send Money" and use n4py@arrl.net as the paypal destination. Or you can mail a cashier's check made out to "Carl Moreschi" for $65. Let me
This is what is now left for sale: Model 218 250 hertz 9 mhz filter for the Orion and Omni's $65.00 including shipping. TenTec Pegasus with LDG PT-11P internal memory tuner. This pegasus and tuner ar
This is what is now left for sale: TenTec Pegasus with LDG PT-11P internal memory tuner. This pegasus and tuner are in perfect condition. The tuner adds about $125 in value to this radio. $700 includ
That sounds like you have microprocessor noise getting into the RF chain somewhere. You might try removing the covers and making sure all the connectors that go to the microprocessor board are pushed
This is what is now left for sale: TenTec Pegasus with LDG PT-11P internal memory tuner. This pegasus and tuner are in perfect condition. The tuner adds about $125 in value to this radio. $700 includ
The biggest thing it adds is direct frequency entry frothe keypad and band stacking registers with the band buttons. There is also provision to correct the frequency error on each band to make the fr
My N4PY Orion control program works with the Orion and Orion II and steppir at the same time. You use the steppir Y cable to allow the steppir controller to just listen on the serial port. My N4PY co
The purpose of a receive only antenna jack is to allow you to use a different antenna for receiving than transmitting. When there is a lot of atmospheric noise such as thunder crashing, it often help
Has anyone figured out if the notches in 2.059d and 2.037j are back in the AGC loop or are still outside the AGC loop? I have been away from home and I cannot test this myself until Sunday afternoon.
I finally got back home and just installed version 2.059d. What I am finding is both the speaker and headphone volime require a higher setting than 2.056. On 2.056 I could set the volume to 50% and t