When using my N4PY Orion control program, the mode is figured out from the frequency. If the frequency is in the CW portion of a band, the mode is CW. If the frequency is in the SSB portion, the mode
I have developed a new Paragon EPROM chip for all Paragons. The new chip greatly enhances the operation of the Paragon. Highlites of the new function Two band stacking registers for each ham band Ico
I have made up a new batch of Omni V chips. These chips are what I am calling my Omni V.9 version 2 chips. In this chip, there is no longer any need to do the extensive serial port mod that was requi
Ryszard Borkowski Maybe you need to add my n4py@arrl.net to your address folder? Carl Moreschi N4PY 121 Little Bell Drive Bell Mountain Hays, NC 28635 -- Original Message -- From: "Carl Moreschi" <n4
My chip adds computer control for logging programs. The chip makes the paragon emulate the Icom 735 so any logging program that works with the Icom 735 will then work with the paragon. I also add som
No, my new Paragon chip is not for the Paragon II. 73, Carl Moreschi N4PY 121 Little Bell Drive Bell Mountain Hays, NC 28635 -- Original Message -- From: "Rick and Karen Bunn" <RRBunn@cox.net> To: "'
I do this all the time with my N4PY Orion control program and my DX Spots program. By running the Orion completely under software control, all these problems are gone. Carl Moreschi N4PY 121 Little B
I have a very nice Tentec Pegasus for sale. Included with the radio are: LDG memory built in tuner ($125 Value) Airpax breaker Power cord Tentec accessory cable Instruction manual Latest version N4PY
I spoke with Gary Barbour at the Tentec hamfest and he said the performance of the Omni VII would be better than the Omni VI and not quite as good as the Orion II. I particularly liked the human fact
Does the ALC light flash when you speak into the mic? There is also a hardware mic gain control in 2.059d. It is in the SSB menu. Carl Moreschi N4PY 121 Little Bell Drive Bell Mountain Hays, NC 28635
It is just an encoder. No keypad. Carl Moreschi N4PY 121 Little Bell Drive Bell Mountain Hays, NC 28635 -- Original Message -- From: "Paul DeWitte K9OT" <k9ot@mhtc.net> To: <tentec@contesting.com> Se
Do a battery reset and then a normal reset. You should always do these when changing firmware levels. Carl Moreschi N4PY 121 Little Bell Drive Bell Mountain Hays, NC 28635 -- Original Message -- From
There seems to be an issue with some Orion II's with 2.037j that causes the baud rate to be off a little. The fix is to set the baud rate at 56000 baud instead of 57600. Carl Moreschi N4PY 121 Little
Direct conversion receivers are prone to pick up AC 60 hertz hum as the result of modulation of the VFO carrier (which is at the operating frequency in a direct conversion receiver) with the 60 hertz
What is the RF gain set at for the sub-receiver? Carl Moreschi N4PY 121 Little Bell Drive Bell Mountain Hays, NC 28635 -- Original Message -- From: "Bernhard Hoidn" <bernhard.hoidn@online.de> To: "Te
I only suggested checking the RF gain setting on the Sub-receiver because an RF gain setting of 0 would cause the sub-receiver S meter reaidng to go to maximum. It sounds like that is not the problem
Yes, I am using 2.059d and have clear audio. Carl Moreschi N4PY 121 Little Bell Drive Bell Mountain Hays, NC 28635 -- Original Message -- From: "John" <fraz1@bellsouth.net> To: <tentec@contesting.com
The rx320 interface works beautifully with BeaconSee when running the Jupiter with my N4PY software. Carl Moreschi N4PY 121 Little Bell Drive Bell Mountain Hays, NC 28635 -- Original Message -- From:
I am running the Orion with version 2.059d firmware. I am noticing that I must run AGC on a very fast setting in order for QSK on CW to work properly. With AGC om medium, some of the transmit signal
I just got an email from ON4UN asking him why he is selling his Orion. He is so happy with his Orion, that he bought 2 Orion II's a few months ago. So this review is completely bogus. Carl Moreschi N