What firmware do you have loaded? You may need to do a battery reset followed by a main reset. Carl Moreschi N4PY 121 Little Bell Drive Bell Mountain Hays, North Carolina 28635 It has developed a str
No, you do not need RTS or CTS. The omni VI is completely CI-V compliant. You need to set the correct baud rate and the correct CI-V address in your program that is trying to access the Omni VI. Thes
No, you are not missing anything. Either connection works the same. The only advantage of the mini-plug connection is you can parallel connect up to 4 CI-V type radios connected over the same serial
There's more specs to crystals then just the frequency. There is the capacitive load either series or parallel and whether the crystal is operated at the fundamental or a harmonic and also the case t
Yes. They use different sockets. The remote pod form the Oiron does not plug into the serial port. Carl Moreschi N4PY 121 Little Bell Drive Bell Mountain Hays, North Carolina 28635 II. for the comput
The pegasus pod will work with an Orion. I am using a pegasus pod on my Orion. Carl Moreschi N4PY 121 Little Bell Drive Bell Mountain Hays, North Carolina 28635 http://track.netzero.net/s/lc?s=197335
The first local osc outputs a frequency of 45 to 75 mhz (45 mhz higher than the operating frequency) in 2.5 khz steps depending on the operating frequency. This frequency is controlled by the onboard
The AT-200PC autotuner from LDG, when used in conjunction with my rig control software, ends up following the rig without having to transmit. You just have to tune one time on each frequency and then
The horizontal lines just represent the maximum range the bandwidth rectangles can move. The break in the line is just to separate the line for the main receiver side and the sub receiver side. If yo
The DSP code in the firmware is doing all the changing to accomplish this. Very little is happeining electronically. Carl Moreschi N4PY 121 Little Bell Drive Bell Mountain Hays, NC 28635 -- Original
It is coming some time soon. Carl Moreschi N4PY 121 Little Bell Drive Bell Mountain Hays, NC 28635 -- Original Message -- From: "Jeff Frank" <jafrank@nyc.rr.com> To: <tentec@contesting.com> Sent: Tue
The Orion recording has more bass and less highs. With a 6 khz filter in the Orion, the audio passband is 3 khz on each side of the carrier. I would expect this to sound bassy and have less highs. Bu
I have one other thought with regards to V1 and V2 on the Orion. On AM, the bandwidth with V1 is actually double the filter size. So a 6 khz filter on V1 is actually 12 khz which is 6 khz each side o
You definitely should not have your tower ground and house ground tied together. Even a nearby lightning strike can cause the two grounds to develop very large voltage differences. Having these tied
The whole question here about grounding is really one of expense. Clearly the best setup is to ground everything together from the tower to the shack with 0 gauge or larger wire. All bonds must prese
The problem with any noise blanker comes down to how they work. When a high noise spike is detected, the audio is blanked for a very short time (like 10 milliseconds). If a strong station comes on th
I had an MFJ 1026 noise cancelor for a while. I found it quite effective at removing various noise sources but there were problems with it. I had an outside noise antenna for it. The noise antenna di
Tentec has this feature in their rx340 for a 10 mhz standard. I wonder how similar it would be for them to make this for the Orion and Orion II. Carl Moreschi N4PY 121 Little Bell Drive Bell Mountain
I have many happy users running my Jupiter and Orion software to control their radios. My webpage is at www.n4py.com. I also have a dxspots and logging program that works in conjunction with my radio
Rick, I recommend the 4 port from Keyspan at www.keyspan.com model USA-49WLC. Carl Moreschi N4PY 121 Little Bell Drive Bell Mountain Hays, NC 28635 -- Original Message -- From: "Rick Williams" <rick.