In the old days, there were no reliable methods to measure power output. Watt meters didn't exist that were in any good unless they cost more than the transmitter. In fact the FCC restrictions for po
Just so you know, I have just added a feature to my Omni VII program that will automatically control the Tokyo Hi Power HL 1.5KFX amplifier through a second serial port. This allows full control of t
No, not at all. My Omni VII frequency is extremely stable and so is the power level. Carl Moreschi N4PY 121 Little Bell Drive Bell Mountain Hays, North Carolina 28635 problems with this rig? A friend
The DSP/AGC artifacts noted by Sherwood in the Orion can be completely eliminated by adding a very small amount of hang time. They were caused by the AGC being so fast that the noise came up between
Tentec had a kit for $25 way back then that added 30 meter transmit and 24 mhz transmit and receive. I added this kit to my Omni A series B back in the early 1980's. From memory, there were a few coi
Yes, you are correct. But you can also run the Omni VII and an rx320 receiver together using my N4PY software for full dual receive. My software will marry the 2 radios together so it will work as th
It works fine to find the callers for the DX station. The receiver is actually almost the same as the Jupiter receiver without the bells and whistles. 73, Carl Moreschi N4PY 121 Little Bell Drive Bel
Yes, there are special orion.ini parms to allow extended transmit coverage with the Orion and Orion II and my N4PY software. Carl Moreschi N4PY 121 Little Bell Drive Bell Mountain Hays, NC 28635 -- O
The rx340 is bad on the close in dynamic range because the DSP in the RX340 only has a 40 db range. So any signal in the roofing filter passband (+- 10 khz) can only have 40 db of AGC applied to it.
It will work with my N4PY software if you configure beaconsee for a tentec pegasus. Carl Moreschi N4PY 121 Little Bell Drive Bell Mountain Hays, North Carolina 28635 _________________________________
The RX340 is excellent down to at least 60 khz where WWVB is located. Carl Moreschi N4PY 121 Little Bell Drive Bell Mountain Hays, NC 28635 -- Original Message -- From: "john ferro" <foxbat426@hotmai
Do you have an antenna selected for SUB RX? Carl Moreschi N4PY 121 Little Bell Drive Bell Mountain Hays, NC 28635 -- Original Message -- From: "G.C." <g.crosta@tin.it> To: "TEN TEC LIST" <tentec@cont
The Omni C was short for Omni D series C. They were only made in digital. So obviously Omni C series B is impossible. In the Original mode, there was an Omni A for analog and an Omni D for digital di
It sounds like you have a bad RUF file. Download the update again from RFSquared and start over. Carl Moreschi N4PY 121 Little Bell Drive Bell Mountain Hays, NC 28635 -- Original Message -- From: "Ed
I have a 61 inch Samsung DLP. I have had it since September, 2003. The set has performed flawlessly, has an unbelievable picture, and I have never had any noise generated from the TV at all. Carl Mor
The Paragon followed the Corsair II. Then later the Omni V, then the Omni VI, then the Paragon II. Carl Moreschi N4PY 121 Little Bell Drive Bell Mountain Hays, NC 28635 -- Original Message -- From: <
The biggest problem is how far is your radio from the antenna. If the antenna runs right over the roof and you are on the 2nd floor with the antenna 10 feet away, you are going to have problems. If t
In a contest exchange, QSL means I received all your information and you are now in my log. Carl Moreschi N4PY 121 Little Bell Drive Bell Mountain Hays, NC 28635 -- Original Message -- From: "DAVID H
It still means the information has been received and you are in my log. Whether or not it is a good thing to do in a contest does not change its meaning. Carl Moreschi N4PY 121 Little Bell Drive Bell
You must configure N3FJP for a tentec pegasus even though you actually have an Orion. This will cause N3FJP to not use a serial port at all, and instead communicate to the N4PY program through the te