The Jupiter can be used equally well with the rx340 as the pegasus with my N4PY rx340 software. Ten-Tec has been very good about making the software interface to the Jupiter be identical to the pegas
Author: Carl Moreschi" <n4py@earthlink.net (Carl Moreschi)
Date: Fri, 2 Nov 2001 14:00:14 -0000
I would just like to add one thing. Just because a signal is digitally generated does not mean it has to sound "digital". Remember, all those beautiful CD's we listen to are 100% digitally generated.
Author: Carl Moreschi" <n4py@earthlink.net (Carl Moreschi)
Date: Sat, 3 Nov 2001 02:02:06 -0000
Rick, If any of your coax connectors had an open to the shield side (very common problem), you would have a lot of excess monitor noise because of poor shielding in the shack. If you then added a lot
I purchased a new computer and decided to get an LCD monitor. It has a 15 inch screen and is very sharp. The huge side effect is I no longer have ANY noise from my computer in the Pegasus or RX340. S
Paul, The Omni A and Omni D are only different with regards to the display. The Omni A is an analog display, the Omni D is a digital display. The original Omni was not a series B. You could call it a
Version 1.51 of my Jupiter/Pegasus software is now available. If you do not have this and would like to have it, please send me an email for details. Carl Moreschi N4PY Franklinton, NC
Version 1.50 of my pegasus software is now available. This version features all the keys on the remote pod being user defineable just like the three function keys. There are over 20 functions that ca
The N4PY Pegasus Control Program also runs fine on the Ten-Tec Jupiter with the Jupiter in "Pegasus Emulation Mode". Carl Moreschi N4PY Franklinton, North Carolina n4py@earthlink.net -- Original Mess
Ken, I made labels for my remote pod so I can remember what they do. I used one of these new electronic label makers to make the labels. I think the remote pod looks neat with the labels on it. Carl
I have just sent out Version 1.49 of my pegasus software. It has 12 new things in it from the previous version. It now has software support for Ten-Tec's new automatic internal tuner for the Pegasus.
Jack, If it was coming in through the antenna right through the case, no Jupiter would work. They have to have RF there in order to transmit! I don't think the problem is anywhere as bad as you are i
I am confused at all the negative feelings I see posted about DSP filtering. In all my years hamming using collins mechanical filters, multipole crystal filters and the like, I have never seen anythi
The pitch should change in your receiver, but your transmitted signal should NOT change. Carl Moreschi N4PY Franklinton, North Carolina n4py@earthlink.net -- Original Message -- From: <DK2GZ@aol.com>
Last week I released version 1.47 of my Pegasus software. Highlites of version 1.47 are: 1) Implemented a new mode called "CWR" for CW reverse. Normal CW mode uses LSB which causes tones to increase
I decided this morning to do an experment to see how resistant my RX-331 is to front end overload. I have a dipole on a separate feedline located about 100 feet from my tower. On my tower, I have a l
Believe it or not, the DSP processor in the RX-331/340 is 16 bit. Carl Moreschi N4PY Franklinton, North Carolina n4py@earthlink.net the program Plus, cannot Ten-Tec outstanding. signal have and front
The only computer control for the Jupiter is in Pegasus emulation mode. Carl Moreschi N4PY Franklinton, North Carolina n4py@earthlink.net -- Original Message -- From: "Carl J. Denbow" <ka8jxg@callsig
The problem is if you are going to hook up a outboard DSP unit or any other accessory to the audio line, the outboard unit will have one side of the audio input grounded. Therefore, you must isolate
They do in all their radios since the Paragon I. Only radios prior to the Paragon I require the magnetic breaker. Starting with the Paragon, ALC is produced from both power output and final collector
New versions for my Pegasus and RX-320 software are now available. Highlights of version 1.46 of my Pegasus software features the following: 1) Full RX-331/RX-340 support to work with the Pegasus in