Mail Archive Search: <+from:n4py@earthlink.net>

Results:

References: [ +from:n4py@earthlink.net: 590 ]

Total 590 documents matching your query.

61. [TenTec] N4PY Software Version 2.07 (score: 1): Author: n4py@earthlink.net (Carl Moreschi); Date: Tue Apr 1 18:24:18 2003; Version 2.07 of my N4PY Pegasus/Jupiter/RX350/Argonaut V/RX340 control program is now available. All registered users should now have the program. If you do not, please send me an email. Highlites of; /archives//html/TenTec/2003-04/msg00015.html (9,116 bytes)
62. [TenTec] an antenna question (score: 1): Author: n4py@earthlink.net (Carl Moreschi); Date: Wed Apr 2 21:47:36 2003; George, You could not of said it any clearer. That's exactly my experience also with radials. I have a very unique vertical that I use on 80, 75, 40, and 30 meters. It is a 60 foot vertical wire runn; /archives//html/TenTec/2003-04/msg00056.html (11,950 bytes)
63. [TenTec] Fw : Orion first impressions (score: 1): Author: n4py@earthlink.net (Carl Moreschi); Date: Tue Apr 8 22:05:12 2003; Most of these "problems" sounds like design choices rather than bugs. Have patience. All this will change as the firmware evolves. That's the great thing about being able to upgrade the firmware so e; /archives//html/TenTec/2003-04/msg00219.html (19,116 bytes)
64. [TenTec] Need 7417 Chip (score: 1): Author: n4py@earthlink.net (Carl Moreschi); Date: Sun Apr 13 22:31:17 2003; I found them at www.circuitspecialists.com/prod.itml/ic0id/2272 I searched on "hex buffer 7417". Carl Moreschi N4PY Franklinton, NC -- Original Message -- From: "WILLIAM MANSEY; WA2PVK" <res0wsci@ver; /archives//html/TenTec/2003-04/msg00329.html (7,980 bytes)
65. [TenTec] Ten Tec vs. Inrad 9 MHz Filters (score: 1): Author: n4py@earthlink.net (Carl Moreschi); Date: Tue Apr 15 16:16:43 2003; Jim, There would be negligible difference by using the inrad filters in the Orion. 99% of the time, the DSP filters won't even need the a narrow roofing filter. The difference between the tentec and; /archives//html/TenTec/2003-04/msg00381.html (11,308 bytes)
66. [TenTec] Computer Contol of the Orion (score: 1): Author: n4py@earthlink.net (Carl Moreschi); Date: Thu Apr 17 11:29:52 2003; Although tentec has not yet released the programmer's manual for the Orion, they have stated that everything you can do from the front panel will be controllable from software. I am planning on relea; /archives//html/TenTec/2003-04/msg00414.html (11,203 bytes)
67. [TenTec] Computer Contol of the Orion (score: 1): Author: n4py@earthlink.net (Carl Moreschi); Date: Thu Apr 17 16:44:07 2003; At this point I don't know for sure. But I think there will be an RX ANT connection on a board in the Orion that can be brought out to the spare jack. This should be very similar to the mod we made f; /archives//html/TenTec/2003-04/msg00423.html (14,192 bytes)
68. [TenTec] Ten Tec vs. Inrad 9 MHz Filters (score: 1): Author: n4py@earthlink.net (Carl Moreschi); Date: Thu Apr 17 19:58:06 2003; Jim, I don't have my Orion yet, but all indications are the stock roofing filters in the Orion should do the job for 99% of the situations. I have an extra 250 hertz filter from my Omni V that I am p; /archives//html/TenTec/2003-04/msg00433.html (14,554 bytes)
69. [TenTec] Enhanced SSB (score: 1): Author: n4py@earthlink.net (Carl Moreschi); Date: Sat Apr 19 16:34:50 2003; Simply because it sounds nice. Carl Moreschi N4PY Franklinton, NC -- Original Message -- From: "George, W5YR" <w5yr@att.net> To: <tentec@contesting.com> Sent: Saturday, April 19, 2003 5:12 PM Subject; /archives//html/TenTec/2003-04/msg00535.html (12,040 bytes)
70. [TenTec] Pegasus: No Output (score: 1): Author: n4py@earthlink.net (Carl Moreschi); Date: Mon Apr 21 23:29:32 2003; Jeff, That really sounds crazy. The only software things that can block CW transmit are not being inside a ham band, TX Loop being on but not connected, and Transmit Disable. It sounds like you have; /archives//html/TenTec/2003-04/msg00583.html (9,133 bytes)
71. [TenTec] Pegasus: No Output (score: 1): Author: n4py@earthlink.net (Carl Moreschi); Date: Tue Apr 22 08:13:33 2003; Jeff, It really sounds like the 12 volt connection to the final board in the pegasus is not connected. Inside the pegasus, this is a heavy red wire that runs from the low pass filter board to the fin; /archives//html/TenTec/2003-04/msg00591.html (11,079 bytes)
72. [TenTec] Slightly OT: SSB vs AM (score: 1): Author: n4py@earthlink.net (Carl Moreschi); Date: Tue Apr 22 19:04:59 2003; Assuming you recorded your voice message on a tape recorder and played it back at half the speed, it would take twice the time to send the message. So we would be using half the bandwidth but twice t; /archives//html/TenTec/2003-04/msg00611.html (9,821 bytes)
73. [TenTec] Slightly OT: SSB vs AM (score: 1): Author: n4py@earthlink.net (Carl Moreschi); Date: Tue Apr 22 21:34:36 2003; Mark, I'm glad you brought up the SSTV analogy. The problem is very similar. You have a certain amount of information to send. If you cut the frequencies in half and keep the time the same, I don't b; /archives//html/TenTec/2003-04/msg00617.html (13,300 bytes)
74. [TenTec] Argo V 10 hz display (score: 1): Author: n4py@earthlink.net (Carl Moreschi); Date: Mon Mar 3 22:00:41 2003; The Argo V frequency smallest step is 10 hertz even though the display goes to 1 hertz. Not a problem at all. Carl Moreschi N4PY Franklinton, NC -- Original Message -- From: "Rob Atkinson, K5UJ" <k5u; /archives//html/TenTec/2003-03/msg00086.html (8,099 bytes)
75. [TenTec] Pegasus and HamScope (score: 1): Author: n4py@earthlink.net (Carl Moreschi); Date: Tue Mar 4 08:18:14 2003; Wayne, Just turn on the "VOX" button on the program radio panel. Adjust the "Vox Gain" slider in the VOX settings window until the radio goes to transmit when HamScope sends audio. Carl Moreschi N4PY; /archives//html/TenTec/2003-03/msg00096.html (7,883 bytes)
76. [TenTec] Argo V 10 hz display (score: 1): Author: n4py@earthlink.net (Carl Moreschi); Date: Tue Mar 4 11:36:26 2003; Rob, The Pegasus, Jupiter, RX320, RX350, RX331,and RX340 do, in fact, all have 1 hertz resolution. Carl Moreschi N4PY Franklinton, NC -- Original Message -- From: "Rob Atkinson, K5UJ" <k5uj@hotmail.c; /archives//html/TenTec/2003-03/msg00103.html (8,406 bytes)
77. [TenTec] WTB Omni VI+ (score: 1): Author: n4py@earthlink.net (Carl Moreschi); Date: Tue Mar 4 16:01:45 2003; In a word, Yes. Carl Moreschi N4PY Franklinton, NC -- Original Message -- From: "Tom A" <althofft@concentric.net> To: <tentec@contesting.com> Sent: Tuesday, March 04, 2003 8:54 PM Subject: Re: [TenTe; /archives//html/TenTec/2003-03/msg00116.html (7,856 bytes)
78. [TenTec] Info on connecting W4PY and Logger (score: 1): Author: n4py@earthlink.net (Carl Moreschi); Date: Tue Mar 4 18:33:07 2003; Keith, You need to configure in LOGGER the folder that my n4py program is installed in. "c:\n4py" is the default but you could have specified another one. Also, make sure logger is using the ten-tec; /archives//html/TenTec/2003-03/msg00124.html (8,984 bytes)
79. [TenTec] Argo V 10 hz display (score: 1): Author: n4py@earthlink.net (Carl Moreschi); Date: Tue Mar 4 18:36:48 2003; But the Argo V will only go to the nearest 10 hertz frequency. So, if my software sets the Argo V at 14.258122, the Argo V will actually go to 14.258120. It really does not matter, but it is clear th; /archives//html/TenTec/2003-03/msg00125.html (8,189 bytes)
80. [TenTec] Precision in Frequency displays (score: 1): Author: n4py@earthlink.net (Carl Moreschi); Date: Tue Mar 4 19:57:49 2003; Stuart, It's not the acuracy here by displaying to a 1 hertz value that's real important. It's the ability to adjust the frequency in 1 hertz increments. I have a mode I call SAM for sync AM that is; /archives//html/TenTec/2003-03/msg00133.html (9,823 bytes)

Current List: 61 - 80
Page: [1] [2] [3] [4] [5] [6] [7] [8] [9] [10] [11] [12] [13] [14] [15] [16] [17] [18] [19] [20]