Search String: Display: Description: Sort:

Results:

References: [ +from:scotty@ashiko.com: 8 ]

Total 8 documents matching your query.

1. [TowerTalk] How is the best way to bend rebar (score: 1)
Author: "Scotty Rathjen" <scotty@ashiko.com>
Date: Sat, 26 Aug 2006 20:50:16 +0100
Hi Gang, Just finished making one rebar cage and have more to do. Bending # 4 (half inch diameter) rebar is not so easy. Can I use a torch to heat up the rebar so that I can easily bend it or does th
/archives//html/Towertalk/2006-08/msg00886.html (7,388 bytes)

2. [TowerTalk] How best to keep the rebar cage centered in the hole? (score: 1)
Author: "Scotty Rathjen" <scotty@ashiko.com>
Date: Wed, 11 Oct 2006 16:20:11 -0700
What is the best way to keep the rebar cage in the center of the hole as I pour the concrete? The rebar cage is held together with wire and when it sits vertical in the hole on the paving stones the
/archives//html/Towertalk/2006-10/msg00341.html (7,493 bytes)

3. [TowerTalk] Hi Ron (score: 1)
Author: "Scotty Rathjen" <scotty@ashiko.com>
Date: Fri, 7 Nov 2008 06:15:01 -0700
I Ground my MA-550 tower by using a wide braided strap to connect the rotating tower to the 3 8-foot long ground rods that surround the concrete base (the 3 ground rod pic is shown in the ARRL Antenn
/archives//html/Towertalk/2008-11/msg00170.html (6,984 bytes)

4. [TowerTalk] Help with Tower Bolt for my crank-up (score: 1)
Author: "Scotty Rathjen" <scotty@ashiko.com>
Date: Fri, 10 May 2013 18:43:45 -0700
Seeking your ideas on my tower hardware issue. I have a US Tower TX-455 Tower that has a bolt that needs replacing. This bolt holds two ends of the wire rope cable (one end of each of the 2 cables wh
/archives//html/Towertalk/2013-05/msg00125.html (8,228 bytes)

5. [TowerTalk] Help needed to wire up Yaesu G-800S Rotor cable to the controller (score: 1)
Author: "Scotty" <scotty@ashiko.com>
Date: Sat, 30 Jul 2016 03:38:06 -0700
My Ham friend had a stroke and cannot find his color-code to pin-number paper for the 5 wires coming from the Yaesu 800S rotor on his tower. What tests using a multimeter, etc. can I perform to the e
/archives//html/Towertalk/2016-07/msg00575.html (6,996 bytes)

6. [TowerTalk] How do I replace the main cable on a motorized telescoping tower? (score: 1)
Author: "Scotty" <scotty@ashiko.com>
Date: Fri, 7 Jul 2017 07:53:30 -0700
Needs some advice on the procedure to replace the main cable on a telescoping 3-section tower that is motorized with positive pull-down. It is a US Tower TX455MDP and was bought 24 years ago from US
/archives//html/Towertalk/2017-07/msg00086.html (7,168 bytes)

7. [TowerTalk] Help Request: Motorized Telescoping tower needs new bearing for 4 groove pulley. (score: 1)
Author: "Scotty" <scotty@ashiko.com>
Date: Thu, 27 Jul 2017 21:53:00 -0700
US Tower model TX-455 MDP (motorized with positive pull-down) uses a 4 groove pulley with the number 3V315SH stamped on it. The bearing is broken. What do you suggest? Is the complete part available?
/archives//html/Towertalk/2017-07/msg00354.html (7,080 bytes)

8. [TowerTalk] Request for replacement bearing information for tower raising fixture (score: 1)
Author: "Scotty" <scotty@ashiko.com>
Date: Sat, 25 May 2019 12:49:18 -0700
I have a US tower TX-455 that tilts over. The bearing in the top of the raising fixture's sheave needs replacing. The matching sheave on the tower has the same bearing and is still in good shape. I c
/archives//html/Towertalk/2019-05/msg00139.html (7,949 bytes)

Current List: 1 - 8
Page: [1]
This search system is powered by Namazu