Search String: Display: Description: Sort:

Results:

References: [ +from:tjednacz@ieee.org: 108 ]

Total 108 documents matching your query.

81. Re: [TenTec] tentec 238B or palstar 1500cv ? (score: 1)
Author: "Thomas Jednacz" <tjednacz@ieee.org>
Date: Mon, 21 Mar 2005 15:34:59 -0500
Another reason is an L tuner only has one match point. A T tuner can have an apparent match and a real match. In the apparent match condition all the energy is going into the tuner and circulating wi
/archives//html/TenTec/2005-03/msg00505.html (7,434 bytes)

82. Re: [TenTec] using amp to load rain gutter (score: 1)
Author: "Thomas Jednacz" <tjednacz@ieee.org>
Date: Thu, 24 Mar 2005 11:21:33 -0500
Would not recommend high power into the rain gutter. I used rain gutter at an apartment many years ago also. High power will put HIGH voltages on the gutter which will tend to ignite the building. Fi
/archives//html/TenTec/2005-03/msg00606.html (9,357 bytes)

83. Re: [TenTec] make zero beating fast and easy (score: 1)
Author: "Thomas Jednacz" <tjednacz@ieee.org>
Date: Fri, 25 Mar 2005 11:34:38 -0500
Better yet and much easier - download "tunewin.zip" from the Internet. Unzip and install. You now have a small waterfall window and can set the side tone of the CW signal in the window. Simply tune t
/archives//html/TenTec/2005-03/msg00645.html (9,982 bytes)

84. Re: [TenTec] TVI partially solved? (score: 1)
Author: "Thomas Jednacz" <tjednacz@ieee.org>
Date: Mon, 2 May 2005 16:24:42 -0400
Paul from Ten Tec has stated that grounding the power supply CASE is also important. An ungrounded case can pick up RF and reradiate it into the power supply circuitry which can get back into the Ori
/archives//html/TenTec/2005-05/msg00018.html (8,959 bytes)

85. Re: [TenTec] (no subject) (score: 1)
Author: "Thomas Jednacz" <tjednacz@ieee.org>
Date: Mon, 23 May 2005 12:22:12 -0400
There is a critical gain setting that sets the point where distortion and popping will occur. The setting is done at the factory but can be done by you if you are careful and get the instructions fro
/archives//html/TenTec/2005-05/msg00375.html (8,639 bytes)

86. Re: [TenTec] ORION BCI (score: 1)
Author: "Thomas Jednacz" <tjednacz@ieee.org>
Date: Fri, 27 May 2005 13:41:43 -0400
Hope you find the problem and have better enjoyment of the Orion. 73, Tom, W7QF _______________________________________________ TenTec mailing list TenTec@contesting.com http://lists.contesting.com/m
/archives//html/TenTec/2005-05/msg00491.html (7,989 bytes)

87. Re: [TenTec] setting up orion to 3 ele steppir (score: 1)
Author: "Thomas Jednacz" <tjednacz@ieee.org>
Date: Wed, 10 Aug 2005 22:29:47 -0400
It works the same with the Orion. Just plug the "Y" into the serial connector on the Orion and set the SteppIR control box for Orion. Been working here with all the radio software that I have just fi
/archives//html/TenTec/2005-08/msg00214.html (8,432 bytes)

88. Re: [TenTec] O2 Scope (score: 1)
Author: "Thomas Jednacz" <tjednacz@ieee.org>
Date: Wed, 21 Dec 2005 10:29:07 -0500
Howdy - just received my O2 on Monday and still learning how much the O2 has been improved. The scope is MUCH better. It is full time and very fast. Very useful to see what is on the band and how wid
/archives//html/TenTec/2005-12/msg00568.html (9,344 bytes)

89. Re: [TenTec] Orion II Optimal Performance Settings (score: 1)
Author: "Thomas Jednacz" <tjednacz@ieee.org>
Date: Sat, 24 Dec 2005 23:36:25 -0500
The Orion II manual has a good description of the various set ups in the back of the manual. Tom, W7QF _______________________________________________ TenTec mailing list TenTec@contesting.com http:/
/archives//html/TenTec/2005-12/msg00727.html (8,096 bytes)

90. Re: [TenTec] Another RTTY story (score: 1)
Author: "Thomas Jednacz" <tjednacz@ieee.org>
Date: Wed, 15 Feb 2006 10:54:50 -0500
On the O2 go to "menu", "other" and at the bottom of the list you will find a line item to select the source of the "line out" and he last line is "line out level" where you can select "low", "medium
/archives//html/TenTec/2006-02/msg00653.html (9,726 bytes)

91. Re: [TenTec] Orion Speech Compressors (score: 1)
Author: "Thomas Jednacz" <tjednacz@ieee.org>
Date: Tue, 21 Feb 2006 20:42:29 -0500
The DSP speech processing is indeed RF and is done in software functionally after the balanced modulator but before the TX equalizer. As a result very impressive compression is achieved (I see averag
/archives//html/TenTec/2006-02/msg01006.html (10,018 bytes)

92. Re: [TenTec] [Orion] Orion V2. firmware A-OK! (score: 1)
Author: "Thomas Jednacz" <tjednacz@ieee.org>
Date: Tue, 21 Feb 2006 20:58:43 -0500
Howdy - thanks for the info. I just checked mine - 40 meters, 2 el yagi, RF 100% and pre amp ON. Tuned in a broadcast and it was more than 60 dB over 9 - off scale. No clicking with notches off. No c
/archives//html/TenTec/2006-02/msg01008.html (11,248 bytes)

93. Re: [TenTec] Replacing Orion RIT encoder - help? (score: 1)
Author: "Thomas Jednacz" <tjednacz@ieee.org>
Date: Tue, 21 Feb 2006 21:04:03 -0500
Howdy, I just replaced the encoder in the 302 remote. Once I got the "solder wick" to work it was not bad. Don't try to remove the metal clip holding the encoder to the circuit board. I cut the wires
/archives//html/TenTec/2006-02/msg01010.html (9,966 bytes)

94. Re: [TenTec] Orion Speech Compressors (score: 1)
Author: "Thomas Jednacz" <tjednacz@ieee.org>
Date: Thu, 23 Feb 2006 14:58:01 -0500
Hi Bob - Yes all true except for the Orion and Orion II speech processor. There is NO distortion even at higher levels of compression. That is because the algorithm used in the DSP does the compressi
/archives//html/TenTec/2006-02/msg01102.html (9,332 bytes)

95. Re: [TenTec] SDR-1000 (score: 1)
Author: "Thomas Jednacz" <tjednacz@ieee.org>
Date: Thu, 13 Jul 2006 09:58:00 -0400
Hello Lee and all - I don't understand your comment on Dxing and contesting on CW. The SDR has only one RX which makes split operation MUCH more difficult especially when all the controls are on the
/archives//html/TenTec/2006-07/msg00349.html (10,979 bytes)

96. Re: [TenTec] 2.037J Speech Processor (score: 1)
Author: "Thomas Jednacz" <tjednacz@ieee.org>
Date: Mon, 11 Sep 2006 15:54:46 -0400
Ray - I don't understand. Did you reduce the mic gain as you increased the speech processor? I have absolutely no distortion running the speech processor up to 9. During this past weekend WAE SSB co
/archives//html/TenTec/2006-09/msg00273.html (9,312 bytes)

97. Re: [TenTec] Omni VI TCXO (score: 1)
Author: "Thomas Jednacz" <tjednacz@ieee.org>
Date: Sun, 21 Jan 2007 14:14:36 -0500
Howdy - just did the TCXO upgrade myself. It took longer to get the tools out and put them away then to do the upgrade. Very simple. Just make sure that you find the 5 volt supply voltage and don't i
/archives//html/TenTec/2007-01/msg00656.html (8,026 bytes)

98. Re: [TenTec] Jupiter USB/Serial Adapters (score: 1)
Author: "Thomas Jednacz" <tjednacz@ieee.org>
Date: Mon, 12 Mar 2007 22:51:08 -0400
Howdy, another solution is the new Navigator interface by US Interface (www.usinterface.com) - I recently bought one of these and it solves all the USB problems. Only one connection to the computer a
/archives//html/TenTec/2007-03/msg00299.html (8,746 bytes)

99. Re: [TenTec] GFCI problem when running high power (score: 1)
Author: "Thomas Jednacz" <tjednacz@ieee.org>
Date: Tue, 27 Mar 2007 15:30:27 -0400
--Things to consider if you are going to use caps. First make sure the caps are UL rated for line voltage duty - VERY IMPORTANT! Second, depending on how you install the capacitors they may increase
/archives//html/TenTec/2007-03/msg00652.html (8,551 bytes)

100. Re: [TenTec] Omni 7 ethernet control. (score: 1)
Author: "Thomas Jednacz" <tjednacz@ieee.org>
Date: Tue, 24 Apr 2007 13:31:12 -0400
No problems - just read all the info provided by Ten Tec and get a router. If you buy the same type of router that is used in the instructions they it is very easy to set it up. Have fun. Tom, W7QF I
/archives//html/TenTec/2007-04/msg00425.html (9,202 bytes)

Current List: 81 - 100
Page: [1] [2] [3] [4] [5] [6]
This search system is powered by Namazu