Mail Archive Search: <+subject:/^(?:^\s*(re|sv|fwd|fw)[\[\]\d]*[:>-]+\s*)*\[AMPS\]\s+Coils\s*$/>

Results:

References: [ +subject:/^(?:^\s*(re|sv|fwd|fw)[\[\]\d]*[:>-]+\s*)*\[AMPS\]\s+Coils\s*$/: 7 ]

Total 7 documents matching your query.

1. [AMPS] Coils (score: 1): Author: Peter_Chadwick@mitel.com (Peter Chadwick); Date: Wed, 2 Jun 1999 15:18:30 +0100; Any suggestions for the best way to wind tank coils? material is 5mm diameter soft drawn copper tube, coil diameter 3-3/8 inches, 20 turns, 5-1/4 inches long. I have a problem getting the tension eno; /archives//html/Amps/1999-06/msg00046.html (7,376 bytes)
2. [AMPS] Coils (score: 1): Author: w7iuv@axtek.com (Larry Molitor); Date: Wed, 02 Jun 1999 22:52:41 +0100; Peter, I wind my large coils on a form that is about 20% or so smaller in diameter then the smooth finish form. Wind on a couple extra turns. When finished winding, the coil expands some and falls of; /archives//html/Amps/1999-06/msg00070.html (7,753 bytes)
3. [AMPS] Coils (score: 1): Author: jono@enteract.com (Jon Ogden); Date: Wed, 2 Jun 1999 18:53:24 -0500; You should see him after a few beers! 73, Jon KE9NA -- Jon Ogden KE9NA http://www.qsl.net/ke9na <-- CHECK IT OUT! It's been updated!!!!! "A life lived in fear is a life half lived." -- FAQ on WWW: h; /archives//html/Amps/1999-06/msg00071.html (7,059 bytes)
4. [AMPS] Coils (score: 1): Author: Peter_Chadwick@mitel.com (Peter Chadwick); Date: Thu, 3 Jun 1999 10:26:40 +0100; Those are control problems, not mechanical ones! 73 Peter G3RZP -- FAQ on WWW: http://www.contesting.com/ampfaq.html Submissions: amps@contesting.com Administrative requests: amps-REQUEST@contesting.; /archives//html/Amps/1999-06/msg00079.html (7,042 bytes)
5. [AMPS] Coils (score: 1): Author: dcoolica@planet.eon.net (Denis); Date: Thu, 03 Jun 1999 08:55:11 -0500; I have found that winding the coil on say a 3 inch diameter pipe or rod and then transfering it to your 3 1/8 inch grove coil form works good. For coil form I use a single piece of phenol or ABS plas; /archives//html/Amps/1999-06/msg00091.html (8,260 bytes)
6. [Amps] coils (score: 1): Author: "carl seyersdahl" <carlseye@tampabay.rr.com>; Date: Fri, 3 Sep 2004 19:06:20 -0400; all of this reminds me of a problem I had several years ago, with an AL811. the top portion of the Tank coil, 80 mtrs, was distorted badly.!! As tho it had been badly overheated. this current discuss; /archives//html/Amps/2004-09/msg00069.html (6,729 bytes)
7. Re: [Amps] coils (score: 1): Author: R.Measures <r@somis.org>; Date: Fri, 3 Sep 2004 18:38:24 -0700; On Sep 3, 2004, at 4:06 PM, carl seyersdahl wrote: all of this reminds me of a problem I had several years ago, with an AL811. the top portion of the Tank coil, 80 mtrs, was distorted badly.!! As tho; /archives//html/Amps/2004-09/msg00071.html (7,587 bytes)

Current List: 1 - 7
Page: [1]