Mail Archive Search: <+subject:/^(?:^\s*(re|sv|fwd|fw)[\[\]\d]*[:>-]+\s*)*\[AMPS\]\s+figuring\s+tank\s+Zbased\s+on\s+loaded\s+Ep\?\s*$/>

Results:

References: [ +subject:/^(?:^\s*(re|sv|fwd|fw)[\[\]\d]*[:>-]+\s*)*\[AMPS\]\s+figuring\s+tank\s+Zbased\s+on\s+loaded\s+Ep\?\s*$/: 8 ]

Total 8 documents matching your query.

1. [AMPS] figuring tank Zbased on loaded Ep? (score: 1): Author: zeitler@attglobal.net (Lane Zeitler Ku7i); Date: Wed, 20 Oct 1999 03:50:53 -0700; When figuring the tank Z in an output pi network is it figued using the expected plate voltage under load or at idle? It makes quite a difference. Lane Ku7i -- FAQ on WWW: http://www.contesting.com/a; /archives//html/Amps/1999-10/msg00560.html (7,990 bytes)
2. [AMPS] figuring tank Zbased on loaded Ep? (score: 1): Author: philk5pc@tyler.net (Phil Clements); Date: Wed, 20 Oct 1999 10:00:18 -0500; It is figured at the intended plate. current you want to pull. Phil, K5PC -- FAQ on WWW: http://www.contesting.com/ampsfaq.html Submissions: amps@contesting.com Administrative requests: amps-REQUEST@; /archives//html/Amps/1999-10/msg00563.html (9,079 bytes)
3. [AMPS] figuring tank Zbased on loaded Ep? (score: 1): Author: measures@vcnet.com (measures); Date: Wed, 20 Oct 1999 10:29:25 -0700; ? u gotta look at the peak AC anode volts, loaded. For a triode, this usually about 250v less than the supply. For a tetrode, this is pretty close to the anode supply volts minus the screen supply v; /archives//html/Amps/1999-10/msg00568.html (8,482 bytes)
4. [AMPS] figuring tank Zbased on loaded Ep? (score: 1): Author: measures@vcnet.com (measures); Date: Thu, 21 Oct 1999 10:24:04 -0700; Good question, Jon For 8877s, 3cx800A7s, 3-400Zs, 3-500Zs and similar high Mu triodes, roughly 250v minimum is what one finds on the spec sheets. cheers - Rich..., 805.386.3734, www.vcnet.com/measur; /archives//html/Amps/1999-10/msg00580.html (8,447 bytes)
5. [AMPS] figuring tank Zbased on loaded Ep? (score: 1): Author: wb4mnf@atl.org (Bob Duckworth); Date: Thu, 21 Oct 1999 15:27:33 +0100; As my kids used to say when little, "But WHYYYYY?" I'm thinking you are talking GG. More P than plate V*I => Lower Z than plate V/I. Source I is more than plate I. Am I right? What about a grounded c; /archives//html/Amps/1999-10/msg00582.html (9,287 bytes)
6. [AMPS] figuring tank Zbased on loaded Ep? (score: 1): Author: measures@vcnet.com (measures); Date: Thu, 21 Oct 1999 16:12:09 -0700; Because roughly 250v-min. on the anode is what you have to work with. If you attempt to go lower that c. 250v, you make IMD go up. If you go for more than 250v, P goes down. yes ? I have no idea wha; /archives//html/Amps/1999-10/msg00583.html (9,745 bytes)
7. SV: [AMPS] figuring tank Zbased on loaded Ep? (score: 1): Author: sm5ki@algonet.se (Hans Goldschmidt); Date: Fri, 22 Oct 1999 08:02:40 +0200; You must be joking Rich? I have in front of me en old manual on transmitting tubes: The RCA AIR COOLED TRANSMITTING TUBES from 1938 and plenty of grounded cathode neutralized finals there. We used ne; /archives//html/Amps/1999-10/msg00585.html (11,522 bytes)
8. SV: [AMPS] figuring tank Zbased on loaded Ep? (score: 1): Author: measures@vcnet.com (measures); Date: Fri, 22 Oct 1999 02:07:05 -0700; ? no ? I remember that they were Class C. Is Class C linear? cheers, Hans - Rich..., 805.386.3734, www.vcnet.com/measures. -- FAQ on WWW: http://www.contesting.com/ampsfaq.html Submissions: amps@con; /archives//html/Amps/1999-10/msg00587.html (8,557 bytes)

Current List: 1 - 8
Page: [1]