Mail Archive Search: <+subject:/^(?:^\s*(re|sv|fwd|fw)[\[\]\d]*[:>-]+\s*)*\[Amps\]\s+Icom\s+551\s+with\s+amplifier\s*$/>

Results:

References: [ +subject:/^(?:^\s*(re|sv|fwd|fw)[\[\]\d]*[:>-]+\s*)*\[Amps\]\s+Icom\s+551\s+with\s+amplifier\s*$/: 8 ]

Total 8 documents matching your query.

1. [Amps] Icom 551 with amplifier (score: 1): Author: Gudguyham@aol.com; Date: Wed, 10 Feb 2010 09:36:54 EST; The Icom 551(D) transceiver believe it or not does NOT have a "ground on transmit" feature for amplifier use. It does however have an 8 vdc @ 2ma output on transmit which is used in turn with an outb; /archives//html/Amps/2010-02/msg00296.html (6,587 bytes)
2. Re: [Amps] Icom 551 with amplifier (score: 1): Author: mikea <mikea@mikea.ath.cx>; Date: Wed, 10 Feb 2010 08:46:22 -0600; The Six Meter Club list List-Id: World Wide Six Meter Club <sixclub.mailman.qth.net> List-Unsubscribe: <http://mailman.qth.net/mailman/listinfo/sixclub>, <mailto:sixclub-request@mailman.qth.net?subje; /archives//html/Amps/2010-02/msg00297.html (8,438 bytes)
3. Re: [Amps] Icom 551 with amplifier (score: 1): Author: "Carl" <km1h@jeremy.mv.com>; Date: Wed, 10 Feb 2010 11:21:09 -0500; The 551 or D also has just about the worst phase noise of any rig built. With strong signals it can wipe out many kHz and with an amp a lot more. I had one for a short time and didnt make any friends; /archives//html/Amps/2010-02/msg00299.html (8,313 bytes)
4. Re: [Amps] Icom 551 with amplifier (score: 1): Author: "Steve Katz" <stevek@jmr.com>; Date: Wed, 10 Feb 2010 08:55:47 -0800; I think it's a standard 24-circuit Molex Mini-Fit connector. I don't recall having any problem getting them... http://www.molex.com/molex/products/group?channel=products&key=minifit_p roducts WB2WIK/; /archives//html/Amps/2010-02/msg00300.html (8,019 bytes)
5. Re: [Amps] Icom 551 with amplifier (score: 1): Author: George Watson <watson@sierracmp.com>; Date: Wed, 10 Feb 2010 09:29:59 -0700; I had a 551D for a long time and never heard any complaints. It looked pretty good on the SA also, I may have the plots around somewhere. I ran it barefoot, and at very reduced power into a MRF151G h; /archives//html/Amps/2010-02/msg00302.html (9,452 bytes)
6. Re: [Amps] Icom 551 with amplifier (score: 1): Author: "Carl" <km1h@jeremy.mv.com>; Date: Wed, 10 Feb 2010 14:45:52 -0500; Nope, not a lemon as the phase noise problem eventually became discussion topics on VHF forums. There may have been mention of production changes but that was after I went with a transverter. Carl KM; /archives//html/Amps/2010-02/msg00304.html (10,369 bytes)
7. Re: [Amps] Icom 551 with amplifier (score: 1): Author: K1SG@aol.com; Date: Wed, 10 Feb 2010 15:23:34 EST; Lou, if you can't easily find the molex connector that fits, you can jury-rig a workable solution just by using Molex pins or even 2 pieces of #22 wire...you're only using 2 conductors out of the 24; /archives//html/Amps/2010-02/msg00305.html (8,406 bytes)
8. Re: [Amps] Icom 551 with amplifier (score: 1): Author: James Colville <jimw7ry@gmail.com>; Date: Wed, 10 Feb 2010 07:16:07 -0800; Standard male Molex plug. Plug and male pins are available at Mouser. www.mouser.com The size is .063 as I remember. 73 Jim W7RY _______________________________________________ Amps mailing list Amps; /archives//html/Amps/2010-02/msg00354.html (8,376 bytes)

Current List: 1 - 8
Page: [1]