- 21. Re: [TenTec] Herc 2 LP Cap? (score: 1)
- Author: <chacuff@cableone.net>
- Date: Tue, 27 Aug 2013 21:12:57 +0000
- If there are two of them in parallel wouldnt good practice be to replace them both? It that is the case something with a lower voltage than I suggested might be in order.. Cecil Acuff Gulfport MS K5D
- /archives//html/TenTec/2013-08/msg00310.html (9,999 bytes)
- 22. Re: [TenTec] Herc 2 LP Cap? (score: 1)
- Author: John Huffman <hjohnc@gmail.com>
- Date: Tue, 27 Aug 2013 17:13:26 -0400
- Jim - Thanks! I appreciate the info. I know you have had Hercs and it is nice to keep these running. I have two, but only one power supply. 73 de K1ESE John http://www.tabmica.co.uk/page7.html <http:
- /archives//html/TenTec/2013-08/msg00311.html (10,132 bytes)
- 23. Re: [TenTec] Herc 2 LP Cap? (score: 1)
- Author: John Huffman <hjohnc@gmail.com>
- Date: Tue, 27 Aug 2013 17:14:22 -0400
- Cecil - Many thanks for the info. Easy to order from Mouser. 73 de K1ESE John Id try this...I think it will be fine... Cecil Acuff Gulfport MS K5DL From: John Huffman Sent: August 27, 2013 3:38 PM To
- /archives//html/TenTec/2013-08/msg00312.html (13,652 bytes)
- 24. Re: [TenTec] Herc 2 LP Cap? (score: 1)
- Author: <chacuff@cableone.net>
- Date: Tue, 27 Aug 2013 21:31:23 +0000
- Another option since it is in parallel with a twin would be to replace both with these.. http://www.mouser.com/ProductDetail/Murata-Electronics/DHRB5AD101M1CB/?qs=sGAEpiMZZMsh%252b1woXyUXj4JRvXjdr5gR
- /archives//html/TenTec/2013-08/msg00313.html (15,015 bytes)
- 25. Re: [TenTec] Herc 2 LP Cap? (score: 1)
- Author: Steve Hunt <steve@karinya.net>
- Date: Tue, 27 Aug 2013 22:32:43 +0100
- C42 is a shunt component on the *input* side of the LPF - the voltage across it is the full output voltage of the four combined PA modules, fundamental plus harmonics. At 14MHz it's reactance is 114
- /archives//html/TenTec/2013-08/msg00314.html (10,089 bytes)
- 26. Re: [TenTec] Herc 2 LP Cap? (score: 1)
- Author: nx7u@nx7u.net
- Date: Tue, 27 Aug 2013 11:31:40 -0500
- Disc-ceramic capacitors for LPF use: I have replaced a lot of HF SS amp LPF caps over time. The best parts are not uncommon, but not terribly simple to find, either. There are two keys: 1. Get the ph
- /archives//html/TenTec/2013-08/msg00318.html (7,670 bytes)
- 27. Re: [TenTec] Herc 2 LP Cap? (score: 1)
- Author: Jim Brown <k9yc@audiosystemsgroup.com>
- Date: Tue, 27 Aug 2013 21:38:55 -0700
- It is the value of DC resistance that would be measured if a high enough voltage was applied to measure the current. It is a DC resistance. The resistance WE are talking about is the resistance that
- /archives//html/TenTec/2013-08/msg00322.html (10,252 bytes)
- 28. Re: [TenTec] Herc 2 LP Cap? (score: 1)
- Author: Richards <jrichards@k8jhr.com>
- Date: Wed, 28 Aug 2013 01:00:29 -0400
- Thanks, JB. That helps. -- K8JHR -- The resistance WE are talking about is the resistance that is added to the equivalent circuit in series with the capacitance represents the power dissipated when t
- /archives//html/TenTec/2013-08/msg00323.html (10,108 bytes)
This search system is powered by
Namazu