Mail Archive Search: <+subject:/^(?:^\s*(re|sv|fwd|fw)[\[\]\d]*[:>-]+\s*)*\[TenTec\]\s+NEW\s+Orion\s+firmware\s*$/>

Results:

References: [ +subject:/^(?:^\s*(re|sv|fwd|fw)[\[\]\d]*[:>-]+\s*)*\[TenTec\]\s+NEW\s+Orion\s+firmware\s*$/: 32 ]

Total 32 documents matching your query.

1. [TenTec] New Orion Firmware (score: 1): Author: "J. Crit Harley" <jcharley@bellsouth.net>; Date: Wed, 19 May 2004 21:44:20 -0400; Well, downloaded from net okay and uploaded to rig okay. BUT on tuning there is no difference in tuning rate whether use step 1, 10 or 100. All step as if set at a step rate of 100. No fine tuning. D; /archives//html/TenTec/2004-05/msg00575.html (7,195 bytes)
2. Re: [TenTec] New Orion Firmware (score: 1): Author: "Jim Reid" <jimr.reid@verizon.net>; Date: Wed, 19 May 2004 15:54:23 -1000; Evidently, can't imagine what, however. Mine is operating very fb. I would perform the download again, and be sure you got 9408 lines. Also be sure that you have "stop on error" checked. 73, Jim KH7; /archives//html/TenTec/2004-05/msg00576.html (6,921 bytes)
3. RE: [TenTec] New Orion Firmware (score: 1): Author: "Jess Young" <w8jy@starband.net>; Date: Wed, 19 May 2004 22:13:07 -0400; I have encountered an interesting problem. My Orion was communicating with my logging program before I shut the program down to download the Firmware update. When trying to install, the program says; /archives//html/TenTec/2004-05/msg00577.html (8,458 bytes)
4. Re: [TenTec] New Orion Firmware (score: 1): Author: "Tommy" <aldermant@alltel.net>; Date: Wed, 19 May 2004 22:33:55 -0400; Wild shot...sounds like you just have something else assigned to the same COM port as you have the Orion assigned? Maybe reboot the PC, delete the previous firmware update from your PC, and then open; /archives//html/TenTec/2004-05/msg00580.html (9,588 bytes)
5. RE: [TenTec] New Orion Firmware (score: 1): Author: "Jess Young" <w8jy@starband.net>; Date: Wed, 19 May 2004 22:42:39 -0400; Nothing else assigned to that port. Have rebooted, deleted the previous firmware update, deleted the new one, re-downloaded and still no luck. The problem started when I attempted to install the soft; /archives//html/TenTec/2004-05/msg00581.html (9,954 bytes)
6. RE: [TenTec] New Orion Firmware (score: 1): Author: "Richard Detweiler" <rdetweil@hotmail.com>; Date: Wed, 19 May 2004 22:19:58 -0500; This may be something to look at, Try in the upate utility settings / setup to insure it is pointed to the right com port. 73's Rich K5SF From: "Jess Young" <w8jy@starband.net> Reply-To: tentec@conte; /archives//html/TenTec/2004-05/msg00582.html (9,738 bytes)
7. RE: [TenTec] New Orion Firmware (score: 1): Author: "Jess Young" <w8jy@starband.net>; Date: Wed, 19 May 2004 23:29:47 -0400; Checked that, and it is correct. The com port will work with other devices, and worked fine with the Orion until I tried the flash update. The problem seems to be internal to the Orion. Guess I will; /archives//html/TenTec/2004-05/msg00583.html (10,243 bytes)
8. RE: [TenTec] New Orion Firmware (score: 1): Author: "NJ0IP" <Rick@dj0ip.de>; Date: Thu, 20 May 2004 07:15:59 -0700; Crit, Check that you have the proper selection of MAIN-RX SUB-RX. If you accidently have the wrong one selected, pushing the step values won't change anything on the receiver you're listening to. I'v; /archives//html/TenTec/2004-05/msg00586.html (8,700 bytes)
9. Re: [TenTec] New Orion Firmware (score: 1): Author: Bob Henderson <bob@cytanet.com.cy>; Date: Thu, 20 May 2004 14:38:40 +0000; I just returned from Dayton carrying my second Orion, which I am delighted to report journeyed well. This morning I downloaded 1.37 and performed the update on my original Orion which was delivered h; /archives//html/TenTec/2004-05/msg00594.html (9,620 bytes)
10. RE: [TenTec] New Orion Firmware (score: 1): Author: "Jess Young" <w8jy@starband.net>; Date: Thu, 20 May 2004 11:31:07 -0400; Well, the problem is now solved and the Orion is updated and communicating with my computer. Thanks to everyone and their helpful suggestions. Paul at Ten-Tec suggested that I disable all my virus ch; /archives//html/TenTec/2004-05/msg00597.html (12,150 bytes)
11. [TenTec] New Orion Firmware (score: 1): Author: Bill Tippett <btippett@alum.mit.edu>; Date: Thu, 20 May 2004 18:00:41 -0400; does not seem to work. If I set "PTT in CW as MOX" in the menu then the rig continues to work in QSK! Not only that but the only effect of grounding the PTT line is that RX audio is muted. The RX its; /archives//html/TenTec/2004-05/msg00609.html (10,049 bytes)
12. Re: [TenTec] New Orion Firmware (score: 1): Author: Sinisa Hristov <shristov@ptt.yu>; Date: Thu, 20 May 2004 18:18:37 -0400; It should also switch Orion to transmit. That would give the exact control of T/R timing to those who need it, provided that the rest of Orion is capable of supporting such a thing. No, with both VOX; /archives//html/TenTec/2004-05/msg00610.html (8,805 bytes)
13. Re: [TenTec] New Orion Firmware (score: 1): Author: Bob Henderson <bob@cytanet.com.cy>; Date: Thu, 20 May 2004 23:16:18 +0000; Hi Bill Bill Tippett wrote: In addition to muting the receiver, the PTT line should be closing the AMP KEY line to your amplifier. I agree that the radio still works in QSK, but of course you can adj; /archives//html/TenTec/2004-05/msg00611.html (9,917 bytes)
14. [TenTec] New Orion Firmware (score: 1): Author: Bill Tippett <btippett@alum.mit.edu>; Date: Thu, 20 May 2004 22:14:58 -0400; YT1NT: MP will not switch to transmit on a key closure. That's how it should be. You are correct...it's been over a year since I used an MP. I now remember I had to depress Vox to activate BOTH Semi-; /archives//html/TenTec/2004-05/msg00620.html (12,013 bytes)
15. RE: [TenTec] New Orion Firmware (score: 1): Author: "Dick Green WC1M" <wc1m@msn.com>; Date: Sat, 22 May 2004 12:42:58 -0400; Scope measurement shows that the CW waveform is much improved in 1.370. On-air tests confirm that CW sounds excellent at all speeds. With the proper rise time setting, keying is no longer hard, short; /archives//html/TenTec/2004-05/msg00684.html (12,702 bytes)
16. [TenTec] New Orion Firmware (score: 1): Author: "Robert Carroll" <rlcarroll@patmedia.net>; Date: Sat, 4 Dec 2004 09:11:31 -0500; I used the new firmware overnight in the 160m cw with no crashes, quite a difference from the previous version. The new RF gain control arrangement seems very effective, though if anyone can explain; /archives//html/TenTec/2004-12/msg00091.html (7,912 bytes)
17. Re: [TenTec] New Orion Firmware (score: 1): Author: "Carl Moreschi" <n4py@earthlink.net>; Date: Sat, 4 Dec 2004 09:31:04 -0500; The Orion RF gain control now works by combining AGC threshold (which is really DSP gain) with RF gain. As you reduce the RF gain setting, AGC threshold is increased. When AGC threshold reaches its l; /archives//html/TenTec/2004-12/msg00092.html (9,330 bytes)
18. RE: [TenTec] New Orion Firmware (score: 1): Author: "Robert Carroll" <rlcarroll@patmedia.net>; Date: Sat, 4 Dec 2004 13:01:23 -0500; Thanks for the nice explanation. Bob W2WG The Orion RF gain control now works by combining AGC threshold (which is really DSP gain) with RF gain. As you reduce the RF gain setting, AGC threshold is i; /archives//html/TenTec/2004-12/msg00105.html (10,034 bytes)
19. Re: [TenTec] New Orion Firmware (score: 1): Author: Martin Ewing <martin@aa6e.net>; Date: Sat, 4 Dec 2004 06:57:39 -0800 (PST); I think we have a problem with Orion's signal processing. Not that it can't do wonderful things and run circles around older rigs. The problem is that the signal processing is not properly documented; /archives//html/TenTec/2004-12/msg00162.html (8,950 bytes)
20. RE: [TenTec] New Orion Firmware (score: 1): Author: "Grant Youngman" <nq5t@comcast.net>; Date: Sun, 5 Dec 2004 22:16:45 -0600; You must be smoking the stuff I've been trying to get some of ... :-) Grant/NQ5T _______________________________________________ TenTec mailing list TenTec@contesting.com http://lists.contesting.com; /archives//html/TenTec/2004-12/msg00174.html (7,741 bytes)

Current List: 1 - 20
Page: [1] [2]