Mail Archive Search: <+subject:/^(?:^\s*(re|sv|fwd|fw)[\[\]\d]*[:>-]+\s*)*\[TenTec\]\s+Need\s+962\s+diagram\s*$/>

Results:

References: [ +subject:/^(?:^\s*(re|sv|fwd|fw)[\[\]\d]*[:>-]+\s*)*\[TenTec\]\s+Need\s+962\s+diagram\s*$/: 6 ]

Total 6 documents matching your query.

1. [TenTec] Need 962 diagram (score: 1): Author: John Farler <k4avx1@windstream.net>; Date: Wed, 13 Mar 2013 19:55:46 -0400; I have a TT 962 power supply that came with the Omni 6+. It has an 24v ac component on the output that I believe indicates the filter caps are bad or perhaps the full wave rectifier. Anyway, I have n; /archives//html/TenTec/2013-03/msg00157.html (6,842 bytes)
2. Re: [TenTec] Need 962 diagram (score: 1): Author: Stuart Rohre <rohre@arlut.utexas.edu>; Date: Wed, 13 Mar 2013 19:24:48 -0500; John, how old is your 962? You an easily check the bridge rectifiers with power off, and capacitor discharged through a resistor, individually. With a VOM, or DVM on ohms X 100, you should have low r; /archives//html/TenTec/2013-03/msg00158.html (8,516 bytes)
3. Re: [TenTec] Need 962 diagram (score: 1): Author: Mike Bryce <prosolar@sssnet.com>; Date: Wed, 13 Mar 2013 20:39:05 -0400; Just an FYI A lot of VOM meters, when reading ohms, have the polarity of the test leads backwards. Mike wb8vge Sent from my iPhone _______________________________________________ TenTec mailing list; /archives//html/TenTec/2013-03/msg00159.html (8,945 bytes)
4. Re: [TenTec] Need 962 diagram (score: 1): Author: "Bob McGraw - K4TAX" <RMcGraw@Blomand.net>; Date: Wed, 13 Mar 2013 19:43:11 -0500; Be sure and tighten the two screws on the large filter cap and be sure the metal bracket holding the filter cap is secure to the chassis. I've found that the metal bracket is often somewhat floating; /archives//html/TenTec/2013-03/msg00160.html (8,704 bytes)
5. Re: [TenTec] Need 962 diagram (score: 1): Author: "Bob McGraw - K4TAX" <RMcGraw@Blomand.net>; Date: Wed, 13 Mar 2013 21:35:17 -0500; Correction on my part. As I had a 962 to repair this evening, I remembered that procedure I had given is for the 961 power supply where the filter is mounted on a angle bracket. The 962 has the filte; /archives//html/TenTec/2013-03/msg00164.html (10,292 bytes)
6. Re: [TenTec] Need 962 diagram (score: 1): Author: Stuart Rohre <rohre@arlut.utexas.edu>; Date: Thu, 14 Mar 2013 13:25:43 -0500; It might be noted that an open in one of the bridge diodes may not cause a fuse blow; but increased ripple and hum may be seen. When testing electrolytics individually, it is easier to use the X100 o; /archives//html/TenTec/2013-03/msg00176.html (8,201 bytes)

Current List: 1 - 6
Page: [1]