- 1. [TenTec] ORION II TX gone (score: 1)
- Author: Tõnno Vähk <Tonno.Vahk@gildbankers.com>
- Date: Wed, 30 Jul 2008 23:06:53 +0300
- Hi, I have lost any TX output from OII. Pwer can be turned up to 100w but no TX out in any mode, everything else seems normal. RX seems to be OK. I saw some messages in archives looking for solution
- /archives//html/TenTec/2008-07/msg00399.html (7,699 bytes)
- 2. Re: [TenTec] ORION II TX gone (score: 1)
- Author: <n4py@arrl.net>
- Date: Wed, 30 Jul 2008 16:39:29 -0400
- Did you do the battery reset? You power off, press and hold the VFO B LCK button, power on, and continue holding it until the radio says "battery failure". Carl Moreschi N4PY 121 Little Bell Drive Be
- /archives//html/TenTec/2008-07/msg00400.html (8,131 bytes)
- 3. Re: [TenTec] ORION II TX gone (score: 1)
- Author: "Barry N1EU" <barry.n1eu@gmail.com>
- Date: Wed, 30 Jul 2008 21:20:04 +0000
- Do you have the keying loops turned off and the Transmitter turned on in the TX Menu? 73, Barry N1EU _______________________________________________ TenTec mailing list TenTec@contesting.com http://l
- /archives//html/TenTec/2008-07/msg00401.html (7,864 bytes)
- 4. Re: [TenTec] ORION II TX gone (score: 1)
- Author: Tõnno Vähk <Tonno.Vahk@gildbankers.com>
- Date: Thu, 31 Jul 2008 09:43:42 +0300
- yes, thanks. Keying loops are off and transmitter is ON. I do have the rig going into TX and showing also 1.0 SWR all the time! Also the pot indicator shows power but the meter does not and also noth
- /archives//html/TenTec/2008-07/msg00405.html (9,025 bytes)
- 5. Re: [TenTec] ORION II TX gone (score: 1)
- Author: <n4py@arrl.net>
- Date: Thu, 31 Jul 2008 07:56:57 -0400
- My bet is the battery reset will fix it. I have had this problem and the battery reset fixed it. Carl Moreschi N4PY 121 Little Bell Drive Bell Mountain Hays, NC 28635 -- Original Message -- From: "Tõ
- /archives//html/TenTec/2008-07/msg00406.html (10,228 bytes)
- 6. Re: [TenTec] ORION II TX gone (score: 1)
- Author: <brent.zook@verizon.net>
- Date: Thu, 31 Jul 2008 11:53:45 -0500 (CDT)
- I had the same problem, only with the Orion I. It was somewhat intermittent, but once it started happening it quickly turned permanent...was a relay. For some reason the power out on the meter on the
- /archives//html/TenTec/2008-07/msg00407.html (9,236 bytes)
- 7. Re: [TenTec] ORION II TX gone (score: 1)
- Author: "pfizenmayer" <pfizenmayer@qwest.net>
- Date: Thu, 31 Jul 2008 10:28:05 -0700
- Have you tried switching the load to ANT 2 ? Is the power supply current changing as you raise the power ???? Hank K7HP _______________________________________________ TenTec mailing list TenTec@cont
- /archives//html/TenTec/2008-07/msg00409.html (10,522 bytes)
- 8. Re: [TenTec] ORION II TX gone (score: 1)
- Author: "John T. Fleming" <W3GQJ@embarqmail.com>
- Date: Thu, 31 Jul 2008 14:25:43 -0400
- Tonno, If all fails, before you send it for repair, remove the front panel and loosen the logic/display boards from the keypad board as well as the logic board from the display board. You do not need
- /archives//html/TenTec/2008-07/msg00410.html (12,085 bytes)
- 9. Re: [TenTec] ORION II TX gone (score: 1)
- Author: Tõnno Vähk <Tonno.Vahk@gildbankers.com>
- Date: Sat, 16 Aug 2008 21:42:46 +0300
- just to let you know that I have tried everything suggested now except for the removing of the front panel in vain. Transmitter is ON, Transverter is OFF. There is a small consumption of ca 5A when T
- /archives//html/TenTec/2008-08/msg00246.html (12,471 bytes)
- 10. Re: [TenTec] ORION II TX gone (score: 1)
- Author: "Denton" <denton@oregontrail.net>
- Date: Sat, 16 Aug 2008 14:54:40 -0700
- Try shutting down both the radio and its power supply for about an hour and see what happens... -- Original Message -- From: "Tõnno Vähk" <Tonno.Vahk@gildbankers.com> To: "Discussion of Ten-Tec Equip
- /archives//html/TenTec/2008-08/msg00254.html (13,118 bytes)
This search system is powered by
Namazu