Mail Archive Search: <+subject:/^(?:^\s*(re|sv|fwd|fw)[\[\]\d]*[:>-]+\s*)*\[TenTec\]\s+OUT\s+OF\s+HAM\s+BAND\s+MODIFICATION\s*$/>

Results:

References: [ +subject:/^(?:^\s*(re|sv|fwd|fw)[\[\]\d]*[:>-]+\s*)*\[TenTec\]\s+OUT\s+OF\s+HAM\s+BAND\s+MODIFICATION\s*$/: 11 ]

Total 11 documents matching your query.

1. [TenTec] OUT OF HAM BAND MODIFICATION (score: 1): Author: Robert Lutz <w2bzr@verizon.net>; Date: Tue, 07 Dec 2004 23:12:23 -0500; Does anyone have the modification to make the Paragon transmit out of band tnx 73 Bob _______________________________________________ TenTec mailing list TenTec@contesting.com http://lists.contesting; /archives//html/TenTec/2004-12/msg00256.html (7,052 bytes)
2. Re: [TenTec] OUT OF HAM BAND MODIFICATION (score: 1): Author: w8au@sssnet.com; Date: Tue, 07 Dec 2004 23:35:53 -0500; At 11:12 PM 12/7/04, Robert Lutz wrote: Does anyone have the modification to make the Paragon transmit out of band Go to logic board, find plug labeled "Ham band" (or similar). Unplug. Done. Been man; /archives//html/TenTec/2004-12/msg00257.html (7,576 bytes)
3. Re: [TenTec] OUT OF HAM BAND MODIFICATION (score: 1): Author: jerome schatten <romers@shaw.ca>; Date: Tue, 07 Dec 2004 20:48:54 -0800; And I would ask as well if anyone has an inkling about a general Tx mod for the Jupiter. All I need is enough RF to tickle an swr bridge for antenna projects, and to use it as an RF sig gen. I know t; /archives//html/TenTec/2004-12/msg00258.html (7,915 bytes)
4. Re: [TenTec] OUT OF HAM BAND MODIFICATION (score: 1): Author: Jim Bull <ke3nk@erols.com>; Date: Wed, 08 Dec 2004 09:33:36 -0500; Bob, On my two Paragon's, the MARS/CAP/60M mod is accomplished by cutting/unsoldering the jumper wire on the logic board (Labeled "HAM") and resetting the processor. The jumper is located directly be; /archives//html/TenTec/2004-12/msg00264.html (8,201 bytes)
5. Re: [TenTec] OUT OF HAM BAND MODIFICATION (score: 1): Author: Mark Erbaugh <mark@microenh.com>; Date: Wed, 08 Dec 2004 13:16:00 -0500; I believe TenTec has a firmware update for MARS operation. You might check with them. When operating in Pegasus mode with computer control, there is a software command you can send to allow out of ha; /archives//html/TenTec/2004-12/msg00276.html (8,445 bytes)
6. RE: [TenTec] OUT OF HAM BAND MODIFICATION (score: 1): Author: "Rick and Karen Bunn" <RRBunn@cox.net>; Date: Thu, 9 Dec 2004 16:50:12 -0500; Same place. Mine was a yellow wire loop labeled HAM and its about 1/3 from the back of the radio on the right side. Not sure what the board is, but it works well. 73 Rick N4ASX Bob, On my two Paragon; /archives//html/TenTec/2004-12/msg00308.html (8,888 bytes)
7. Re: [TenTec] OUT OF HAM BAND MODIFICATION (score: 1): Author: joel hallas <jrhallas@optonline.net>; Date: Mon, 17 Jan 2005 11:29:30 -0500; Jim, Great tip, thanks much! I found the jumper just where you predicted, cut it and it seems to operate perfectly on 60 m. I checked it b4 I did a processor reset and it seems to be just fine. Is th; /archives//html/TenTec/2005-01/msg00686.html (9,417 bytes)
8. Re: [TenTec] OUT OF HAM BAND MODIFICATION (score: 1): Author: joel hallas <jrhallas@optonline.net>; Date: Mon, 17 Jan 2005 12:14:43 -0500; Folks, Sorry to say the chart formatting was lost in transition. Here it is, hopefully readable. BTW, I put the appropriate offset channels in memory to make sure I end up in the right place, per the; /archives//html/TenTec/2005-01/msg00691.html (9,844 bytes)
9. [TenTec] Out of ham band modification (score: 1): Author: "Harry Coates" <WA8HC@att.net>; Date: Tue, 18 Jan 2005 11:15:58 -0500; Joel, Which ham band are you using for 60M, 40 or 80?? Are the LP filters wide enough to cover 60M?? Harry Harry N. Coates WA8HC@att.net _______________________________________________ TenTec mailing; /archives//html/TenTec/2005-01/msg00746.html (7,167 bytes)
10. Re: [TenTec] Out of ham band modification (score: 1): Author: "Vic Klein" <vhklein@ptd.net>; Date: Tue, 18 Jan 2005 12:23:16 -0500; Just to jump in, Harry, the Paragon shifts the LP filters on a frequency basis, not a band basis (you can hear the relays shift as you tune). The appropriate filter is in place when receiving 60m and; /archives//html/TenTec/2005-01/msg00761.html (8,076 bytes)
11. Re: [TenTec] Out of ham band modification (score: 1): Author: joel hallas <jrhallas@optonline.net>; Date: Tue, 18 Jan 2005 21:01:18 -0500; Thanks Vic, yes Harry Vic has covered it nicely. The only problem with this arrangement is that in memory tune mode the RIT doesn't work. You need to pop out of MT and use the RIT, or manual tuning,; /archives//html/TenTec/2005-01/msg00777.html (9,398 bytes)

Current List: 1 - 11
Page: [1]