Mail Archive Search: <+subject:/^(?:^\s*(re|sv|fwd|fw)[\[\]\d]*[:>-]+\s*)*\[TenTec\]\s+Omni\s+\-\s+C\s+Finals\s*$/>

Results:

References: [ +subject:/^(?:^\s*(re|sv|fwd|fw)[\[\]\d]*[:>-]+\s*)*\[TenTec\]\s+Omni\s+\-\s+C\s+Finals\s*$/: 6 ]

Total 6 documents matching your query.

1. [TenTec] Omni - C Finals (score: 1): Author: weaver615 <weaver615@gmail.com>; Date: Sun, 11 Feb 2018 15:11:45 +0000 (UTC); Hi All; I have an Omni - C and I when I first got it, signal reports were consistently 59 - 20 over....Now, Signal reports are little to no audio and no signal to nothing at all. I have the Dirve all; /archives//html/TenTec/2018-02/msg00080.html (7,949 bytes)
2. Re: [TenTec] Omni - C Finals (score: 1): Author: MadScientist <dukeshifi@comcast.net>; Date: Sun, 11 Feb 2018 09:18:11 -0600; Well, best to use a wattmeter and dummy load to test your output power. Alternately, you can place an ammeter in series with one of your power leads from the power supply and measure current. You sho; /archives//html/TenTec/2018-02/msg00081.html (8,397 bytes)
3. Re: [TenTec] Omni - C Finals (score: 1): Author: w0ep <w0ep@w0ep.us>; Date: Sun, 11 Feb 2018 11:54:35 -0600; I tend to think it is more than the antenna. In my Omni, if the drive is high I get an ALC light. Are you seeing that with drive set high? Sent from BlueMail _______________________________________; /archives//html/TenTec/2018-02/msg00082.html (8,284 bytes)
4. Re: [TenTec] Omni - C Finals (score: 1): Author: Michael Goins <wmgoins@gmail.com>; Date: Sun, 11 Feb 2018 12:19:40 -0600; Bill, Have you run the rig into a dummy load to check the power out? That's the first thing I'd do. Check it with a 50 ohm load. mike, k5wmg _______________________________________________ TenTec mai; /archives//html/TenTec/2018-02/msg00084.html (9,378 bytes)
5. Re: [TenTec] Omni - C Finals (score: 1): Author: Shawn Upton via TenTec <tentec@contesting.com>; Date: Sun, 11 Feb 2018 19:04:48 +0000 (UTC); A final can blow and let the driver do the tx, albeit at a low power. I would use a wattmeter on CW first, see if it is the final or perhaps a bad mic connection. Might want to reseat any modules an; /archives//html/TenTec/2018-02/msg00085.html (8,034 bytes)
6. Re: [TenTec] Omni - C Finals (score: 1): Author: Ken Brown <kenradiobrown@gmail.com>; Date: Sun, 11 Feb 2018 10:47:58 -1000; Until you connect it to an RF wattmeter and a 50 Ohm termination (dummy load) everything is just guess work. The MFJ tuner may have a semi-accurate forward power indicator. If you had logged the read; /archives//html/TenTec/2018-02/msg00086.html (9,506 bytes)

Current List: 1 - 6
Page: [1]