Mail Archive Search: <+subject:/^(?:^\s*(re|sv|fwd|fw)[\[\]\d]*[:>-]+\s*)*\[TenTec\]\s+Omni\s+V\s+DB25\s+to\s+DB9\s+wiring\s*$/>

Results:

References: [ +subject:/^(?:^\s*(re|sv|fwd|fw)[\[\]\d]*[:>-]+\s*)*\[TenTec\]\s+Omni\s+V\s+DB25\s+to\s+DB9\s+wiring\s*$/: 6 ]

Total 6 documents matching your query.

1. [TenTec] Omni V DB25 to DB9 wiring (score: 1): Author: "A.W. B." <a7bull@hotmail.com>; Date: Fri, 20 May 2005 19:20:59 +0000; Ok...I used to know this...The wiring diagrams in the Omni V manual are for DB25 to DB25 for a PC but I want to have a DB9 at the computer end for a standard serial port. Do I wire the DB9 like the d; /archives//html/TenTec/2005-05/msg00326.html (6,966 bytes)
2. Re: [TenTec] Omni V DB25 to DB9 wiring (score: 1): Author: "Roger Borowski" <K9RB@bellsouth.net>; Date: Fri, 20 May 2005 16:04:25 -0400; Andy, By far, the easiest way is to use any standard serial (straight through) cable, either 9 pin or 25 pin, and your local Radio Shack has an adapter that with adapt one side to be what you need. I; /archives//html/TenTec/2005-05/msg00328.html (8,591 bytes)
3. Re: [TenTec] Omni V DB25 to DB9 wiring (score: 1): Author: "denton" <denton@oregontrail.net>; Date: Fri, 20 May 2005 13:09:57 -0700; see if the local computer shop has the plug in db25 socket that goes into the slot in the computer. -- Original Message -- From: "A.W. B." <a7bull@hotmail.com> To: <tentec@contesting.com> Sent: Frida; /archives//html/TenTec/2005-05/msg00329.html (8,018 bytes)
4. Re: [TenTec] Omni V DB25 to DB9 wiring (score: 1): Author: "Steve Baron - KB3MM" <SteveBaron@StarLinX.com>; Date: Fri, 20 May 2005 17:14:14 -0000; for in I would map the DB 25 pins to the corresponding pins. You are only talking about 3 wires. Do not connect all of the wires to the radio! It uses them for its own purposes. Look in the manual. _; /archives//html/TenTec/2005-05/msg00331.html (8,105 bytes)
5. Re: [TenTec] Omni V DB25 to DB9 wiring (score: 1): Author: "Steve Baron - KB3MM" <SteveBaron@StarLinX.com>; Date: Fri, 20 May 2005 18:32:08 -0000; You really do not want to do that. Take a look at fIGURE 5-10a ON PAGE 5-9. Note that only pins 1,2,3 and 7 areused. here is a good reason for that. Look at paragraph 6-24and table 6-1 on page 6-99.; /archives//html/TenTec/2005-05/msg00332.html (10,219 bytes)
6. Re: [TenTec] Omni V DB25 to DB9 wiring (score: 1): Author: "jack" <jfriend31@comcast.net>; Date: Fri, 20 May 2005 17:33:00 -0600; you can also use a DB25 to DB9 adapter for that if you have one handy. i have used such an adapter many times. jack ak7o _______________________________________________ TenTec mailing list TenTec@con; /archives//html/TenTec/2005-05/msg00336.html (8,627 bytes)

Current List: 1 - 6
Page: [1]